insta360 evo 3d models

The Mantis-Sub camera plate for Insta360 Pro/Pro2 is a replacement for the camera plate that ships as standard with every Mantis-Sub camera housing for Insta360 Pro, in case of loss or damage. Two variants are included: standard length, and short...

This setup lets you mount an Insta360 Go to the back of your Remix V2 and produce incredible videos. Included is the original wide 3D printed arm designed for use with the Insta360 Go's 1/4-20 mount. This exact design has been used in all 3PV videos...

Important note: the Caddx Peanut Power adapter does work to power and to start/stop recording on the Insta360 Go 2 but to work reliably the "rim" that slots into the track on the rear of the Peanut camera needs to be removed. I did it by carefully...

My camera filters are 67mm, so I use a 52mm to 67mm metal adapter plate to fit them to the insta360 One r body. I used Esun PLA+ 20% infill and a 10mm brim, plus Cura v4.8.0. to slice. I've added rounded corners, so there is no need to print...

A: The official Insta360 One BT remote does work with OneX, but it's out of stock – permanently. Many third-party BT remotes resemble the official one, yet most cannot establish a connection with One/OneX. ...You can verify this information in the...

I'm not sure why Insta360 added that little hump below the camera cage, instead of on the top, but it makes it impossible to mount the cage directly onto the roller mount. This adapter will fix that. You'll need one additional M3 bolt and nut. I...

This custom underside 3PV mount for the Insta360 GO camera is specifically designed to be used on an Armattan Rooster frame, ensuring seamless integration and optimal performance. Printing in TPU yields outstanding results, as it effectively dampens...

Original Insta360 Mount Design https://www.thingiverse.com/thing:4802617 by Heizi. ... Remixed Design for GoPro Tabs https://www.thingiverse.com/thing:4872143 by ivarivar 52mm Adapter Design https://www.thingiverse.com/thing:4795929 by Garry1953

canopy - any hard material 0.15mm insta360 mount, antenna mount - Flex 0.15mm Camera angle is 36-43 degrees. Canopy is designed for Runcam Nano 2, fits Runcam Racer Nano, also barely fits Caddx Baby Ratel. Antenna mount should go through a square...

... Remixed Chariot X and Tête AIO EVO head support for magnet 15x4 (cart) and steel disc (17x2). Remixed chain support (15x15) and cable cover cap. Lowered the head block by 3mm in Z to maintain a safety margin between the cart bottom and nozzle.

... for the twigXL. ...PRovides a vertical mount for the Insta360 GO (also a remix) and a TrueRC Bardpole antenna mount, which works surprisingly well on the XL besides its length. ... You print it, you buy me a coffee: https://www.buymeacoffee.com/gilg

Insta360 Go2 Anti Vibe Mount for Micro Alien as requested by jdpworks. Not flight tested yet, but is similar to the Micro Apex version so it should be fine. ... Designed for printing with TPE, though should be fine with TPU also.

I'm using this mount for my 1" motorbike handlebars to secure my __insta360 GPS Smart Remote__. To prevent the bracket from twisting on the handlebars, I strongly advise a maximum 1mm thick rubber pad between handlebars and bracket. ...For mounting,...

Insta360 One R case with a hot shoe mount for the Boosted Battery case. CAD file included if you want to edit it... There is a video about it on Youtube https://youtu.be/hHGeSJWp91o If you can watch it I would appreciate it a lot. Thanks! ...

Insta360 One R mount for the GEPRC Mark4 drone frame. This mount is heavy with a thickness of 4mm and will absorb energy during crashes. 3 models are available depending of the desired tilt : 20°, 25° and 30°. ... I suggest printing it on the side...

This is a case to store an Insta360 Go 2 camera and the pendant. I printed it on a Creality Ender 3 V2 in PLA.  Blue for the base and clear for the top. ... Shouldn't need support so long as you print the top of the lid on the print...

My friend bought an Insta360 ONE X and wants a Drifter, but they are not shipping yet so I have created OpenDrifter. 12.31.2018 Insta 360 ONE X fits very well. Modified nub.stl. 12.29.2018 First Draft. Untested, but should work with minimal...

This is a custom mount designed to securely attach an Insta360 camera to a Tinyhawk II Freestyle drone. It's specifically engineered for the wider frame of the TH Freestyle 2, ensuring a precise fit and optimal performance. ...The mount can be easily...

This is a replacement for the rubber lens protector that comes with the Insta360 One R. It's a bit wider so it can be used when the camera is mounted in the frame of the BetaFPV X-Knight 360. ...I angled the flaps a bit so it sits nice and tight.

Will fit the Insta360 GO 2 snugly enough to not fall out during normal flight. It depends on a friction fit so you may need to fine-tune the upper and lower contact pads depending on how well dialed in your printer is. This mount is designed to...

My remix of https://www.thingiverse.com/thing:4496361 to use Small mount to use with the Toothpick PicklePod2 Insta360 holder (https://www.thingiverse.com/thing:3944156). ...Print Settings Printer: Delta Rafts: No Supports: Yes Resolution: 0.14...

This is a straightforward mount designed specifically for attaching an Insta360 Go camera to either a Beta85 or Beta95 drone using the Umma85 Clean and Dirty kit. ...The mount should be compatible with both the original and version 2.5 of the Umma85...

This is Insta360 Go Camera Vertical mount so you can shoot FPV Rider style videos on BetaFPV 95X V2 CineWhoop using your Insta360 go Camera and you can record 5 minutes max videos easily. It fits with supplied two screws on vibration damped cam...

This is my mount to put an insta360 onto a Tinyhawk II Freestyle. It has the correct spacing for the wider frame of The TH Freestyle 2. ... It can be printed from TPU without support if you have your printer dialed in.

Insta360 go holder for 85mm/95mm FPV drone. tested on uz85 You may also print base plate from BetaFPV. ... (7)Camera Mount A for Beta85X / Beta95X（Material：black PLA） ...

Insta360 One Mount with New Twist-Lock V2 Design. Published Open Source with Parametrized Plate and Lock Thickness. Fusion360 File Attached for Customization. Separate Supports, 0.1mm from Object, for Easy Slicer Use. ... Watch Old Version Twist-Lock...

My remix of https://www.thingiverse.com/thing:4792436 to use Small mount to use with the Toothpick PicklePod2 Insta360 holder (https://www.thingiverse.com/thing:3944156). ...Print Settings Printer: Delta Rafts: No Supports: Yes Infill: 20 Filament:...

Approximate unofficial cad model of insta360 camera 1 inch. I made it only to design a mount for my mark4 quadrocopter frame, but I tried to reflect the main nuances.Bracket rotated 27 degrees to the horizont. ...In assembly, you can change the angle...

Instead of the original 45-minute battery my One R is mounted with a 3-hour boosted battery with a 3D printed Bracket :-) Version 2 you can find here...

This magnet lens cover is designed for insta360 OneRS 1 inch 360 camera. My camera is in a aluminum frame, original cover can’t be used in this situation. This design can protect the lens without remove frame. ... You need to buy Magnet 2xD6-3mm Test...