insulin pen holder 3d models
349202 3d models found related to insulin pen holder.thingiverse
Insulin pen holder with a place for wipes and storage bin for needles. ...No supports required.
thingiverse
# Parametric Insulin Pen Holder Keep your insulin pens standing upright to save space in the fridge. ... Easily adjust the model sizing by changing the parameters defined in the "ss" spreadsheet in the FreeCAD model.
thingiverse
Insulin pen holder ------------------------- This holder was originally intended to be attached to fridge doors with double-sided tape but can be used wherever you want. Compatible pens ------------------------- - Compatible with any pens with 1,6...
thingiverse
This is a snap fit insulin pen holder to mount inside of your refrigerator using double sided 3M tape
prusaprinters
The insulin pens that I was using at the time that I designed this holder came five to a box. ... The holder is open and for keeping the pens from rolling around. Print SettingsPrinter: Creality Ender 3 ProSupports:NoLayers:0.2...
thingiverse
My Insulin pens take up too much room in the fridge when left in their boxes, so I created this holder to better store them. Sized originally for Toujeo, but Humalog was a tight fit. Pictures are of the v3 model, but I have also included v4. v4...
thingiverse
I didn't want my insulin pens just laying in the fridge. I have Lantus pens. I'm pretty sure all brands are basically the same so this should work for all. ...The pen holes are a bit tight but the pens slide in and out without getting stuck.
thingiverse
created this to keep an easy way to keep inventory, and store insulin in my fridge.
thingiverse
Compatible with any pens with 1,6 cm diameter like Lantus or Apidra adjusted the spacing to allow more flex in the clamps and made this printer friendly to print standing up instead of laying down.
thingiverse
This simple holder is made to hold 8 BD insulin pen needles. ... The original file is available in OnShape as a public document to copy if you want to make tweaks. Search for "Insulin Pen Needle Holder"
thingiverse
A minimalist insulin pen needle holder. It can hold 1 or 2 needles, new or used, securely until they can be disposed of properly. I use it with Novo Nordisk pens and BD nano needles. ... Be sure to install it by sliding this holder down from the top of...
thingiverse
I don't use Levamir. ...So I removed the name from it and added a mounting clamp to the base
thingiverse
this is a remix of another kwikpen insulin pen which has two sperate caps instead of one. this helps not to drop the needles when ever you remove the pen. ... original design: https://www.thingiverse.com/thing:4552663
thingiverse
If you would like larger/smaller variants, you can find design for this part here in OnShape: https://cad.onshape.com/documents/a6d8d05cc0b7309d53965bc7/w/8515853fd43909d0e522c134/e/9b0141e7ac32faacd3a58dcd Don't forget to also check out the glucose...
prusaprinters
This snugly holds 10 BD Ultrafine pen needles that can easily be removed before or after use. If you would like larger/smaller variants, you can find design for this part here in OnShape:...
thingiverse
Ever since I started using my Freesyle Libre, I had no pouch where I could savely store my Pen needles, so I designed this "cap" to hold 3 Needles at once to carry them savely in my pockets together with my pen. ... Notice: The print doesn't look...
thingiverse
This is a vertical stand to store up to five Lantus insulin pens.
prusaprinters
This is a vertical stand to store up to five Lantus insulin pens. Print Settings Printer Brand: Creality Printer: Ender 5 Rafts: No Supports: No Resolution: .04 Infill: 25% Filament: Sunlu PETG Black Category: Other
thingiverse
A simple holder for insulin pen refill cartridges. It is designed so that it can be printed on the flat side with no supports. ... Use double sided 3M tape to adhere to the inside wall of your refrigerator.
thingiverse
Its just another support for an insulin pen and corresponding needles. There are two formats of different heights, 50mm and 100mm, otherwise they are identical (the base is 44mm x 22mm). The hole for the pen has a diameter of 17mm, while the slot...
thingiverse
This is an Insulin Pen holder for two pens along with a place for holding alcohol wipes and a bin for the pen needles. Holes for insulin pens are 21mm x 21mm. ...No supports required.
thingiverse
Set of holders for a Rysodeg flexitouch insulin pen. When I am out and about I wanted something that I could easily slip in my pocket. Designed to be a little insulated and a top cap that will hold 1 needle safely. Printing in PLA recommended...
thingiverse
3x3 Insulin vial holder for Fridge (9 vials) 3x3 Base Dimensions: 90mm x 90mm Holds insulin vials in fridge. ... Easy insertion and removal of vials Fits Humolog 10mL vials or other vials with 23mm diameter
cults3d
Insulin holder with capacity for 5 dispensing pens and enough space to place a cooling gel. ... And needle holder base with capacity for 7 needles
thingiverse
My dad asked me to print something to hold his two different vials of insulin. He was using a duct-taped contraption before. He wanted them to stay together so he could turn them upside down to draw with the syringe. He needs the window to see the...
thingiverse
Remixed this Vape pen holder i thought was neat to fit two insulin pens - measured my victoza, lantus, ozempic, and basaglar and tried to find a happy medium to stand them up to save room on my desk and make them easier to find/grab should fit any...
thingiverse
I created this holder/dispenser to keep the newest pens on top and oldest on the bottom. This design holds around 10 pens. The inside measures 6.75"x.8" so it should hold most pens. I know for sure it will work with the lumjev, humalog, lantus, and...