intex hose to pvc adapter 3d models

An adapter for 32mm INTEX pool hose to 18mm garden hose

This adapter allows you to connect a standard US garden hose (GHT, FHT) to an Intex above ground pool drain. ... [Onshape: Intex Drain...

This adapter allows you to connect a standard US garden hose (GHT, FHT) to an Intex above ground pool drain. Onshape: Intex Drain Connector Print Settings Notes: There is quite a bit of overhang in this model's threads (up to 65º in places), but...

This is an adapter from the Intex above ground pool pump to a garden hose. (The water in the picture inst because it leaks its because the water that was already in the filter came out before i put the hose on) I made this because i had a lot of dirt...

This thing is meant to connect an Intex pool inlet (3th image) to a standard garden hose click connector (4th image). One of the things you can do with it is connect a pool vacuum cleaner (one that needs water to go in it) to the inlet. So you don't...

Wanted a regular hose adapter instead of a quick disconnect. I am thinking for structural sound it might be better printed on its side. Threads might be stronger. Haven't printed yet. Will update after printed. ... BIG thanks to mredmon for the...

In order to connect the hose (32 mm inner diameter) of a pool vacuum cleaner to the water outlet fitting (goes to the pump). ... The diameter of the thread is 83 mm and the pitch is 2.5 mm.

Just added a tube to keep the drain plug on the inside from closing while it drains.

Printing required supports and when it printed it supported the threads that ended up a mess. ...I used a hot soldering iron to re flow the PETG that I used to print this. ...I could make out the threads and hand traced them.

I designed this adapter connect the Intex **_Pool Drain Connector (part no. ...10184)_** to the Hose that came with my **_Intex Autocleaner (198PO)_** The adapter has female 1 1/16 garden hose thread and male "custom" threads for the Intex Hose. ...

This is an Intex 58-59mm Threaded Male to 1 1/2" Adapter. I used this so that I can connect up my system to the standout output with the plunger. ... I had added a skimmer, so everything else is using 1 1/2" PVC.

Intex hose adapter

An adapter that slides over 40mm PVC and connects to flexible pool hoses (the type that pool cleaners use). I designed it for plumbing wash water to a grey water storage tank. ...The taper doesn't fit as tight in the pool hose as I had hoped, but works...

Adapter for 1HP QP bomb to intex hose

Intex 39 mm to 32mm Pool Hose Connector Adapter

Intex 39 mm to 32mm Pool Hose Connector Adapter

... and the "work around" was more than $10. I got the threads for the PVC from mcmaster and the garden hose threads form the link to thingiverse. ...To clarify, this is a female 3/4" GHT (Garden Hose Thread) to male 3/4" NPT (National Pipe Thread).

This simple adapter allows the direct connection between a 50mm vacuum hose and any two inch (50mm) pvc fitting. ...&nbsp;&nbsp;</p><p><br>The STL is in two sizes - the short one is pictured, I printed the longer one because I had a particular use for...

I use this end-cap for an 32mm PVC pipe to connect the 13mm drainage hose from the wash dryer machine. The inside of the end-cap is conical shape from 32.5 to 31.5 mm. It is easy to slide on the 32mm pipe and with a light push it sits tight without...

This adapter allows joining a large Intex 1.5" hose to a Summer Waves / Polygroup 38mm hose. The Intex end needs an Intex gasket and the Summer Waves end needs an O-ring. ... The Intex end was a bit tight, shrinking by 0.5mm on the X and Y axis may...

Intex Hand Pump Hose to Electric Air Pump adapter. ... Tested with the following Intex part numbers: * 11830, Spa/Cover Inflation Hose * 11285, Black Nozzle and Hose Fits most Intext hand pumps:...

This adapter allows joining a large Intex 1.5" hose to a small Intex 1.25" hose. The large end needs an Intex gasket and the small end needs an O-ring. The small end is a bit low poly, but adding some teflon tape fixed that. ... The large end was...

... I also printed the 38mm (1.50") to 32mm (1.25") adapter (found on thingiverse) to connect this hose to the sand filter pump. Here is the pump filter adapter I used: https://www.thingiverse.com/thing:954874 If you print one please post a pic of it.

Intex 32mm Outlet Adapter back from Filter and 40mm Hose Pool Skimmer to Outlet Adapter Both are pulled through the rubber in the pool wall and fixed with the hose from outside. ... Printing with 0.3 works, Support for 40mm Adapter needed.

This adapter allowed me to hook up the smaller Intex pump when my newer larger pump (Model 635) died. This will connect the small hose from the 1000gph pump to the larger intake hose on the larger pools. ...

... Material Continuum on Thingiverse. ... This is an adapter to keep the Intex kayak air hose (vinyl 1kpa boats) connected to the Colman low pressure Quickpump air pump, so you can put it on the ground and walkaway for a few minutes while it does its work

... Material Continuum on Thingiverse. ... This is an adapter to keep the Intex kayak air hose (vinyl 1kpa boats) connected to the Colman low pressure Quickpump air pump, so you can put it on the ground and walkaway for a few minutes while it does its work

this is suposed to be connected inside the pool into the pump intake hole to clean the bottom of the pool. i included the STEP so you can create another stuff reusing with the thread... ... the thread prints without supports and seals tight ( its a...

I still had to purchase the hose to carry the water to a better area away from the house.The knob is a press-fit (at least on my printer) for an M5x25 bolt typically found in printer fastener kits. The hole is tapered slightly so use a nut to pull...

Customized version of https://www.thingiverse.com/thing:1246651 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=1246651