ioptron 3d models

Simple Handbox holder for iOptron CEM25 on Vixen tripod

The missing original battery cover is actually a replacement iOptron SkyTracker cover.

Adapt my trusty Meade Tripod to work seamlessly with the iOptron CEM25 mount.

This is for use on the IOptron GEM 28 Telescope Mount. It allow for the GPS unit to be held in place on the mount without tape, screws, or other physical fasteners. Side on and off as needed. ...

This is a bracket to mount the iOptron iPolar onto Celestron's CGEM Telescope Equatorial Mount. The design includes a support ring that is easily removed after printing. ... The two horizonta holes are 3.2mm to thread manually to M4 screws.

This bracket secures the Ioptron handcontroller firmly to one of the tripod legs. My printer settings include 0.2 layer height and 30% infill, all printed in high-quality PLA material. The print temperature for my TEVO_LM was precisely set at 205...

The iOPTRON AZ Mount Pro handset holder does not firmly support the handset, so I made a holder that keeps it safely in place. It uses the same holes and screw than the original support, and it can safely be kept in place when storing the mount, if...

I designed this to hold the iOptron handset rather than hang it by the built-in lanyard. I have a permanent mount rather than a tripod setup so used this with an Al bracket to bolt to the pier. ...The hole in the back is 5mm (which may need easing out...

The iOptron CEM40 telescope mount ships wit the 8407+ handset, but does not have a holder, so it just dangles with no place to attach it. To remedy this, I designed a holder for the handset that attached to the tripod leg (2 inch diameter). The two...

This is a custom holder for the iPolar camera manufactured by iOptron. The camera is usually sold together with a holder dedicated for exact factory-made mount. But I performed a big custom equatorial fork mount, so there was no holder matching to my...

Replacement knobs for iOptron CEM40 mount saddles. The original knobs are too small and are hard to tighten as well as painful to your fingers. These are nice and big, and will clear the mount when rotated. You will need some additional...

This model is a holder for the GPS module on an equatorial mount (CEM26) from iOptron.

This model is a holder for the GPS module on an equatorial mount (GEM28) from iOptron.

This model is a holder for the GPS module on an equatorial mount (GEM28) from iOptron.

3D replacement parts to change the iOptron CEM70G iGuider camera out with a ZWO mini camera.

Remote holder for Ioptron CEM25 for standard 1.5'' tripod Print in PETG on 100% infill

Vixen dovetail which fits the iOptron Photron RC6. ...Printed on a Aquila X2 in 2 separate parts to be snapped together.

... to put them at risk of damage from dew and debris. This fits perfectly on the iOptron SmartEQ, and it should also fit seamlessly on the iOptron SmartEQ Pro. ...Furthermore, this is fully compatible with a polar scope illuminator already installed.

Hand controller holder that slips into the gap in the iOptron tri-pier legs. Turn it 90 degrees and slip into the top, then turn it opposite and slide it down to the bottom. ...It'll be a loose fit, but good enough to hold the hand controller.

The iOptron CEM40 has a through-hole on the saddle through which you can insert various cables for cable management. Unfortunately, as far as I know, it only comes with one bracket to keep the cables organized and prevent them from bulging upward and...

iOptron iGuider Guide Scope Adapter This will replace the adapter that comes on the iOptron "iGuider" guide scope. It is designed to use the same screws. The flanges allow for standard 1/4-20 6mm screws to be used. This will allow you to mount the...

An extender for the knobs on the iOptron CEM40 saddles; they are small, metallic, and painful to tighten / untighten. Just pop these on and you're golden. ... This is a better version of what I tried to accomplish with this thing:...

## iOptron LiteRoc Foot Cover The feet on the LiteRoc tripod are steel which is nice but is not very forgiving when placing the tripod on concrete and then bringing the tripod indoors to place it on a wooden floor to find scratches. They should be...

Simple GPS holder for the (as of this upload) current iOptron 40/70 mounts with 28mm counterweight shafts. I designed mine for the CEM40, but it will work with any of their mounts with the same diameter counterweight shaft (I believe that includes...

Put both files in the same directory (threads.scad and iOptron Shaft.scad). It takes a long time to render - go get a cup of coffee and breakfast while you wait. It prints at about six hours @.1 mm / layer with good thread finish for working parts....

The iOptron CEM40 telescope mount ships with the 8407+ handset, but does not have a holder, so it just dangles with no place to attach it. To remedy this, I designed a holder for the handset that attached to the tripod leg (2 inch diameter). The two...

This support is for placing the hand control of the iOptron Mini Tower II when it's not in use. To install this holder, just undo slightly the original round knob and insert it into the holder's hole. It may be required to apply a little bit of glue...

This mount adapter is designed for pairing the lightweight iOptron SkyGuider Pro mount with the QHY PoleMaster for exceptional polar alignment results. The screw holes are 4mm and precisely sized for Ruthex M3 screw inserts, available on Amazon...

;) This is an add-on box for the 10th generation Intel NUC that can be easily placed on an iOptron CEM40 mount or on a vixen rail. It contains 3x 12V outputs (for CEM40, camera and other device), 2x PWM adjustable outputs for heating tapes (The...

Dovetail base for iOptron CEM40. May work with other mounts, but I haven't tested. Replaces the base that comes with iGuider and allows using any guider scope with the saddle of the CEM40. Should be fixed to the saddle with 2x M3 tapered head screws....