ipad 2 holder 3d models
1189559 3d models found related to ipad 2 holder.prusaprinters
This is for the iPad 2, which released in 2011.Install the Microsoft RDP software to remote control a PC. ...I mainly use this iPad to control octoprint and SDR software.
thingiverse
Clips that clip on to a LifeProof case for an iPad 2. I'm using two with a short string to hold the iPad on the back seat in front of my toddler on long car rides. ...Works great =) Printed on its side.
thingiverse
I had an old iPad 2 lying around and decided to mount it to my Ender 3 Pro as an Octoprint controller. I printed it on edge with supports for the right section. I was concerned about weight and balance so added v-slot extrusions on 3 sides. ...
prusaprinters
I had an old iPad 2 lying around and decided to mount it to my Ender 3 Pro as an Octoprint controller. I printed it on edge with supports for the right section. I was concerned about weight and balance so added v-slot extrusions on 3 sides. It also...
thingiverse
I needed a holder for my iPad Mini 2 to attach to a flat surface, so I made this remix. I removed the handle and flatted the back. ... I've added a v3 with m3-sized holes so you can screw it to something
prusaprinters
Tablet Holder iPad Air 2 serving for mounting in VESA 100 mm x 100 mm TV bracket.Material: PLA (PETG).Supports: Yes.Layer height: 0,2 mm.Connecting material: Concussion head screws 6 mm.NOTE: The thread of the top tablet fuse must be plainted with a...
prusaprinters
I needed a holder for my iPad Mini 2 to attach to a flat surface, so I made this remix. ...I removed the handle and flatted the back.</p> <p>I've added a v3 with m3-sized holes so you can screw it to something</p> <h3>Print Settings</h3>...
thingiverse
This is a holder for the iPad Mini 2 that will mount to the Ikea Skadis Pegboard system. ...
thingiverse
... of 15mm because there is only a very narrow bottom what the print can be held. Only fits the iPad air 2 The lightning plug is very difficult to get through the hole but I succeeded. :-) Glue the lightning plug with super glue. ...Measure it well.
thingiverse
This iPad holder supports the iPad 2 & 3. It can be adjusted for the optimal viewing angle by sliding the adjustable drive at the front of the holder. A little bit of grease will help move the drive gear; it needs to fit tight, so wear it in a little...
prusaprinters
It consists of a custom holder for the iPad, and 3 generic parts that allow the tablet to move around.For the assembly you'll need:2 M5 bolts, at least 25mm long (anything more won't impact the function, but won't look as sleek), 2 M5 nuts...
thingiverse
The simplest design i could come up with to hold an Apple Ipad Air 2 with the Dji Mavic controller. I used CA and kicker to bond the parts. Print 2 of the pins. UPDATE: version 2 files added, not fully tested as yet.. ...PETG or ABS
myminifactory
Hope you will be as pleased with it as my son was when he could watch movies in the car. ... I made it in ABS
thingiverse
Push Connecter into iPad holder with connecter arm facing the shorter half of the iPad holder 4. line up holes on the Car Mount to connecter piece with the arm looking like \\ 5. Push connecter tube into Car mount 6. ...Turn clockwise until...
prusaprinters
I was handed down an ipad air 2 and i want to use it for long road trips for navigation and movies for the passengers!Its a three piece design where i super glued the ipad holder to the mount behind it.Hardware: m3x40 bolt with hex nux from extras...
thingiverse
iPad Mini Holder for Concept-2 indoor rowing trainer. It's intended to use iPad-Mini with cover. Just flip the cover over the mount panel. ... I sticked a thin rubber tape on the socket to prevent iPad to slip.
thingiverse
IPAD 2 LCD screen holder. i split the file because it had to fit my ender 3. but i glued my together and it works great. ... this case is just for the actual LCD without some form of glass in front of the LCD.
thingiverse
... the two parts together. Although its a tight fit, I’ve also used a bit of hardware ( nuts/bolts/washers) to secure things Hardware iPad holder to stand 1/4” 20TPI 1” long hex head bolt Washer & nut Base plate to stand M6 X40 bolt Washer and Nut
thingiverse
... are small but hold the ipad very good. Print them <b>standing on the side</b> to avoid breaking of the hook due too layer splitting. In the end i printed 4 long holders so i can easy get the ipad horizontal. ... Any comments are always welcome.
prusaprinters
Version1 (beta) I wanted to use my iPad pro 12.9 (2018) with my DJI Mavic 2 Pro. ...I looked at getting a Mavmount bracket, but thought I could simple make something, at least for the short term. Using supergimps excellent Base plate -...
thingiverse
Snuggly holds iPad or tablet (in its case) on the Mavic Air 2 remote controller. No need for extended USB wire. The DJI provided wire is long enough to go with this tablet holder. Print on edge. PLA is fine. Good solid strength. ...Very little...
thingiverse
Customized version of http://www.thingiverse.com/thing:172661 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=172661 Instructions Using the following options:...
thingiverse
Remake of a clever and simple design tablet holder. ...This one can securely hold iPad Mini in the DJI Air2 / Air2s controller.
thingiverse
Customized version of http://www.thingiverse.com/thing:172661 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=172661 Instructions Using the following options:...
thingiverse
This is a two peace print, designed for the Concept 2 Rowing Machine, which holds your ipad, or smart phone (does depend on the size of the phone). I have included .skp files for anyone who would like to edit. ... Enjoy!