ipad 2 holder for car 3d models
2927532 3d models found related to ipad 2 holder for car.prusaprinters
I was handed down an ipad air 2 and i want to use it for long road trips for navigation and movies for the passengers!Its a three piece design where i super glued the ipad holder to the mount behind it.Hardware: m3x40 bolt with hex nux from extras...
thingiverse
This is a holder for a mini iPad to allow its easy positioning for GPS usage. The view angle is 30 degrees and the width of the holder is set to the mini iPad 4 thickness: both of these can be changed, along with all the other measures, in the...
thingiverse
Printing: Infill: 40-100% Sopports: No Rafts: No Layer height: 0.2 Print high model is recommended to do 20-25 mm wide brim, so that the model is not blown off at higher layers. It is better to print the hooks themselves with the maximum contact...
cults3d
Printing: Infill: 40-100% Sopports: No Rafts: No Layer height: 0.2 Print high model is recommended to do 20-25 mm wide brim, so that the model is not blown off at higher layers. It is better to print the hooks themselves with the maximum contact...
thingiverse
This is a Simple Ipad holder, it is adjustable for many different kind of Tablets /Ipads /whatever. There are 3 Holes in the Baseplate with an Angle of 120 degrees, so a Standart Ram Mount plate just fits perfectly. ...There is also enough space at the...
prusaprinters
We needed a way to put an iPad on a car seat so that our daughter can watch her favorite YouTube shows from her own car seat - the eventualsetup almost looks like a in-flight entertainment :-)A second version of the holder (original),...
thingiverse
I found the original iPad holder to be 3mm too short, so I remixed, made it 3mm longer as well as countersunk the holes
thingiverse
For modern sport-seats it's quite hard to find a decent iPad holder for the back seats, so I decided to create one. It will be fixed at the seat using a simple belt, so it should work almost everywhere. It was designed for iPad Air 2, but may work...
thingiverse
As simple tablet holder that will hold an iPad mini 5 on a 2" diameter tripod leg
thingiverse
... of 15mm because there is only a very narrow bottom what the print can be held. Only fits the iPad air 2 The lightning plug is very difficult to get through the hole but I succeeded. :-) Glue the lightning plug with super glue. ...Measure it well.
thingiverse
I had an old iPad 2 lying around and decided to mount it to my Ender 3 Pro as an Octoprint controller. I printed it on edge with supports for the right section. I was concerned about weight and balance so added v-slot extrusions on 3 sides. It...
prusaprinters
I had an old iPad 2 lying around and decided to mount it to my Ender 3 Pro as an Octoprint controller. I printed it on edge with supports for the right section. I was concerned about weight and balance so added v-slot extrusions on 3 sides. It also...
thingiverse
I use 2 apple pencils because 1 always runs out of batteries. ...So the other is a backup. For those of you maniacs like me, I altered this file to hold 2 pencils. ... Thanks!
cgtrader
The Ipad holder for car seat head rest is an easy to 3D print and install DIY device. It's been specifically designed to require no supports during 3d printing. All that's required is for you to download and 3d print your models, couple together...
thingiverse
ipad mini stand for car and other places I made the support for ipad mini to use over the mirror that is in the back seat of the car to see my daughter, I put the support over the mirror, but I made it with a larger opening to be able to put it in...
cults3d
ipad mini stand for car and other places I made the support for ipad mini to use over the mirror that is in the back seat of the car to see my daughter, I put the support over the mirror, but I made it with a larger opening to be able to put it in...
thingiverse
Ipad stand for ipad, ipad 2, ipad air, ipad mini, ipad mini 2, etc..
thingiverse
Part 1 Holds iPad Mini Part 2 Mounts to Mirror with tabs and Velcro strips The two sections get connected with a 1/4" bolt and nut. Instructions Print each part. Connect the Mirror section to your...
thingiverse
I remixed dimensions for the iPad 8, on which I tested and it fits perfectly. Should work on iPad 7 as well, though not tested. ... Cheers
thingiverse
Just a quickly shortened version of the upper mount for the iPad mini (without case)
thingiverse
C'est vrai qu'il faut un iPad, un Expert Tepee et une imprimante 3D.... Mais si vous avez les trois + une grande famille, alors ça va vous intéresser ! La charnière s'assemble avec une tige filetée de 5 et 4 écrous. ...Print Settings Printer: ...
thingiverse
I needed a holder for my iPad Mini 2 to attach to a flat surface, so I made this remix. I removed the handle and flatted the back. ... I've added a v3 with m3-sized holes so you can screw it to something
prusaprinters
Tablet Holder iPad Air 2 serving for mounting in VESA 100 mm x 100 mm TV bracket.Material: PLA (PETG).Supports: Yes.Layer height: 0,2 mm.Connecting material: Concussion head screws 6 mm.NOTE: The thread of the top tablet fuse must be plainted with a...
prusaprinters
I needed a holder for my iPad Mini 2 to attach to a flat surface, so I made this remix. ...I removed the handle and flatted the back.</p> <p>I've added a v3 with m3-sized holes so you can screw it to something</p> <h3>Print Settings</h3>...