ipad 2 tripod mount 3d models
1194696 3d models found related to ipad 2 tripod mount.thingiverse
I liked the design by DIY3DTech but I wanted this to hug my tablet a little tighter. I adjusted the slot size and the bolt hex head hole on the bottom. The bolt head hole was made so that it would be easily printable without any supports. ... Other...
cults3d
I liked the design by DIY3DTech but I wanted this to hug my tablet a little tighter. I adjusted the slot size and the bolt hex head hole on the bottom. The bolt head hole was made so that it would be easily printable without any supports. ... Other...
thingiverse
I needed to attach my iPad Air 2 to a tripod. I found a lot of examples but they all assumed there was no case on the iPad. I didn't want to remove my case every time so I just designed my own. This will fit an iPad Air 2 with a full smart case. The...
thingiverse
This is a mounting frame to place an iPad inside an Otterbox case on a tripod to use it for an automated photobooth. The frame is in three pieces, one slides on, the other two are held on first by the T nut used to mount to the tripod. The nuts I...
thingiverse
i have always been a little bit concerned when using the tripod mount with my iPad, there was always the danger of the iPad slipping sideways and falling off. No worries now! I've added some side clips and a middle slider. Add the middle slider to...
thingiverse
I've needed an iPad-Pro 11" mount for my good old Manfrotto tripod. * Two M4 nuts and M4 x 22mm Hexagon screws are required. I've used the following "Things" for my project: - M4-Nut-Placeholder: https://www.thingiverse.com/thing:794519 -...
thingiverse
This is a simple iPad-3 mount for a regular tripod. It contains 6 things, requires 2 pieces of aluminum bar 1/2" x 1/8" (about 12.8mm x 3.2mm), one M3x16mm screw and one M6x12mm hex bolt. Print 2 copies of side.stl and decide whether you want to use...
cults3d
... hole was made so that it would be easily printable without any supports. I also added a slot for an additional pin that's on my tripod mount. ... Other hardware I used: - 1 1/4"x8" hex head bolt - 1 1/4" nut - 1 1/4" flat washer - 1 1/4" wing nut
thingiverse
This thing will allow an iPad or similar device to be mounted on a tripod for use while using Zoom and other software platforms to conduct virtual classes and meetings. The two holes in the base may need to be rethreaded using either a 1/4-20...
thingiverse
... was made so that it would be easily printable without any supports. I also added a slot for an additional pin that's on my tripod mount. ... Other hardware I used: - 1 1/4"x8" hex head bolt - 1 1/4" nut - 1 1/4" flat washer - 1 1/4" wing nut
thingiverse
Needed a larger holder for 8th gen iPad with a Zugu Case,18mm thick. ...Have the tripod holder as one piece and also in two piece tongue and groove for smaller printers
thingiverse
This is a way for you to attach your iPad to any 1/4-20 thread tripod. You'll need a few things to make this design work which I will try to make clear below Any suggestions for design improvement are welcome IMPORTANT: Cover all surfaces that will...
thingiverse
An adapter to hold an iPhone (6 to 7 plus) or an ipad mini for mounting on a tripod with a standard 1/4"-20 screw on a tripod head. ...Designed with Fusion 360 Print Settings Printer Brand: RepRap Printer: Prusa i3 Rafts: No Supports: Yes Resolution:...
thingiverse
Mount for iPad mini using stm case. ... Will also fit iPad air model.
thingiverse
... adhesion. The threads are: 1/4" - 20 UNC for the tripod mount 1/2" - 13 UNC for the rest of the threading I had tap and die for these on hand in a good old Canadian Tire tap and die kit so that is what I went with, hopefully it is pretty common.
thingiverse
This Ipad Mini Holder is designed to fit with a otterbox defender case on it.
thingiverse
I've had trouble finding a tripod mount that will hold it steady during long time-lapse photos. I constructed this holder, which fits the iPad while it's still in a ruggedized sleeve. ...The 1/2" nickel plated steel bar is tapped with a 1/4-20 thread...
thingiverse
As simple tablet holder that will hold an iPad mini 5 on a 2" diameter tripod leg
thingiverse
A tripod mount for an iPad mini. ... Needs a 1/4" nut from a hardware store (mine was 3¢ from Lowe's).
thingiverse
Slide an Ipad mini in from the side and on the bottom there is a hole for the mount screw for a tripod. Position the tripod screw nice and straight the first time you place the screw so threads will form properly. PLA makes a nice mount filament for...
thingiverse
I bought on Amazon a mount for an iPad on a tripod and the 1/4" screw did not fit completely in the mount (not deep enough). ...I designed a disk with the right dimentions in order to ovecom this problem with success.
thingiverse
iPad Air 2 mount Material: NYLON PA12 1.75 Infill: 60% NO SUPPORTS! ... ENJOY!
thingiverse
A wall mount for an iPad 2 and any others that share the same dimensions. The iPad drops into the top, fits snugly enough not to have any movement when you're touching the screen, but can still be slid up and out of the mount easily enough. I did...
thingiverse
I designed this iPad 2 wall mount to hold an iPad in a fixed position so that touching the iPad won't wobble it. The cable is hidden in the back and has a strain relief. The iPad can easily detached from the cable and slid out of the wall mount to...
thingiverse
This wall mount for the Ipad 2 is designed for permanent installation (in my case the iPad serves as a dashboard for home automation). Since I didn't want the power supply cable to be visible, a permanent power supply behind the Ipad is required...
thingiverse
My spare tripod had a smaller mounting mechanism, the largest side of the square being around 31mm, then the smallest side 25mm This is a simple remix of the square type of mount made to be a bit smaller to fit these kinds of tripods. ...Mine is quite a...
thingiverse
I adapted for the Ipad 2 an existing 3d design from Thingiverse which originally was for the Lenovo tablet mount. The original design was in one piece so I had to separate it so I could print in two materials. I have changed the dimensions to adapt...
youmagine
... use glue if the fit is not tight. The corners should be adjustable with friction,if you have any questions feel free to email me at sphetz@ymail.com or read more at my blog http://sphetz.blogspot.com/2015/02/3d-printed-adjustable-ipad-air.html#more