ipad 3 wall mount 3d models

This is a wall mount for the iPad 3. I made this because I wanted a dashboard for Home Assistant, which is my home automation platform. ...This is a dock I can put my iPad into, as it has an integrated 30pin cable for charging, and I can also quickly...

Simple Wallmount in two pieces Designed for my Charging Wall, since i load all my devices on on Place.

This is a small wall mount for the iPad 3 / 4. This can be best printed on his side, with just the quick print settings in Cura. You can mount the wall mount on a standard 80 x 80 wall box where you normally would put a switch or electric socket. I...

( http://www.kabebijin.jp/ ) These models fit to iPad mini 3. I uploaded normal version and divided version for small workarea printers. ...(10㎝ x 10cm) I recommend to use stainless #10 needles, but it could be diffucult to buy them ( at low price )...

( http://www.kabebijin.jp/ ) These models fit to iPad mini 3. For iPad mini 4, use http://www.thingiverse.com/thing:1890434 For other tablets, use https://www.thingiverse.com/thing:3562681 I uploaded normal version and divided version for small...

iPad Air 3rd Generation Wall mount. The holes for the screws have a diameter of 2,5mm for screws. There are two recesses where magnets can be inserted and glued. However, it also works very well without magnets. IMPORTANT NOTICE: Please make...

You can make your iPad 2, 3, or 4 appear to hover against the wall, held only by this holder that you've printed. Instructions Print it out on some sort of futuristic printing machine. ... Screw it to...

Needed a wall mount for an iPad 2 for use as a POS/order device in a kitchen. Ideally it would sit as flat to the wall as possible, and be small, certainly not get in the way of functionality. So I made this. ...Enjoy.

A simple design for wall mounting an iPad Mini (version 1, 2 or 3 as they are the same size essentially). I am planning to use this for a HomeAssistant control panel. Align the bottom to the bed (CTRL+L in S3D), no supports should be needed. ...

Wall Mount for Ipad Air 3

... longer and I am working on a larger wall mount to suit the series 4. If you would like additional information please visit my blog post on this design: https://www.candco.com.au/2019/09/28/apple-ipad-mini-series-2-3-wall-mount-for-home-automation/

https://www.thingiverse.com/thing:3884431 made a very nice wall case for de Ipad Mini 2 & 3. ...However, I did not like the grooved face plate and made a smooth version of it :) Enjoy!

I was looking for an iPad wall mount that can completely replace a 3 gang light switch. I printed this frame, which can be nailed around the old switch frame. Then I placed the Simplidock plate on top of my 3d print (can be glued or even held into...

This wall mount fits iPads with size 240mm x 169.5mm x 7.5mm.

iPad mini wall mount

Ipad wall mount, apple design.

transparent acrylic wall mount case for Ipad

Wall Mount for Ipad in Case

iPad Gen4 Wall Mount (including support for 3D Printing)

Simple ipad wall mount :) fits well with normal charging cables

Modified the size of the iPad wall mount. ... You can place a iPad 2020 12.9" into the holder with a smart folio applied to it.

This is a wall mount iPad holder which uses 4 corners to mount the iPad similar to a picture frame. ...This version of the mount is designed to be mounted to the wall using double sided tape.

This is a wall mount iPad holder which uses 4 corners to mount the iPad similar to a picture frame. ...This version of the mount is designed to be mounted to the wall using double sided tape.

Allows you to mount the Ipad 2 to the wall with a slight downward facing angle. ... Works great in the bedroom or for mounting where little ones can watch movies but not be able to reach the Ipad.

iPad 12.9' Wall Mount It's a universal mount modeled to fit my old iPad 12.9'. It should work with majority of iPad models, or similar tablets. Please check dimensions if not sure. I will be gluing this mount to the wall using glue tapes instead of...

This iPad wall mount prints in two pieces. You need to print two of them, obviously. ...Then they are assembled with some glue between the pieces (tongue & groove).

I Couldn't find any wall mounts that let hold my Ipad Pro and soft cover at the same time so I designed my own.

Wall mount for the first Ipad. Now in use as display for the 'home automation'. ...14-01-2017_ Added other top mount, for better/flat mounting to the wall

I designed this iPad 2 wall mount to hold an iPad in a fixed position so that touching the iPad won't wobble it. The cable is hidden in the back and has a strain relief. The iPad can easily detached from the cable and slid out of the wall mount to...

A simple wall mount for iPad Air Gen 1. (might also fit iPad Air2 - not tested). The wall mount has holes for countersunk screws but can also be attached using strong double-sided tape. Includes a version with logo for vertical use with the...