ipad case tripod mount 3d models
526702 3d models found related to ipad case tripod mount.thingiverse
This design works with the front mount of http://www.thingiverse.com/thing:827169. ...I redesigned the part to work with iPADs that had cases. ...This design works with iPad Minis in Portrait and Landscape recording.
thingiverse
It is based on the design from Samkass (thanks Samkass!) and although I didn't customize it in the 'Customizer' I used TinkerCad to adjust some of the sizes of the walls, you can even edit it here to fit whatever you like:...
thingiverse
... Air 2 with a full smart case. The maximum thickness is 11.5mm. The tripod mounting plate attaches with a 1/4-20 screw and hex nut. ... I printed this with supports and used PETG because I plan to keep this in my car and didn't want it to warp.
thingiverse
This is a mounting frame to place an iPad inside an Otterbox case on a tripod to use it for an automated photobooth. The frame is in three pieces, one slides on, the other two are held on first by the T nut used to mount to the tripod. The nuts I...
thingiverse
Needed a larger holder for 8th gen iPad with a Zugu Case,18mm thick. ...Have the tripod holder as one piece and also in two piece tongue and groove for smaller printers
thingiverse
i have always been a little bit concerned when using the tripod mount with my iPad, there was always the danger of the iPad slipping sideways and falling off. No worries now! I've added some side clips and a middle slider. Add the middle slider to...
thingiverse
I've needed an iPad-Pro 11" mount for my good old Manfrotto tripod. * Two M4 nuts and M4 x 22mm Hexagon screws are required. I've used the following "Things" for my project: - M4-Nut-Placeholder: https://www.thingiverse.com/thing:794519 -...
thingiverse
This is a simple iPad-3 mount for a regular tripod. It contains 6 things, requires 2 pieces of aluminum bar 1/2" x 1/8" (about 12.8mm x 3.2mm), one M3x16mm screw and one M6x12mm hex bolt. Print 2 copies of side.stl and decide whether you want to use...
thingiverse
This thing will allow an iPad or similar device to be mounted on a tripod for use while using Zoom and other software platforms to conduct virtual classes and meetings. The two holes in the base may need to be rethreaded using either a 1/4-20...
cults3d
... hole was made so that it would be easily printable without any supports. I also added a slot for an additional pin that's on my tripod mount. ... Other hardware I used: - 1 1/4"x8" hex head bolt - 1 1/4" nut - 1 1/4" flat washer - 1 1/4" wing nut
thingiverse
... was made so that it would be easily printable without any supports. I also added a slot for an additional pin that's on my tripod mount. ... Other hardware I used: - 1 1/4"x8" hex head bolt - 1 1/4" nut - 1 1/4" flat washer - 1 1/4" wing nut
thingiverse
This is a way for you to attach your iPad to any 1/4-20 thread tripod. You'll need a few things to make this design work which I will try to make clear below Any suggestions for design improvement are welcome IMPORTANT: Cover all surfaces that will...
thingiverse
Mount for iPad mini using stm case. ... Will also fit iPad air model.
thingiverse
An adapter to hold an iPhone (6 to 7 plus) or an ipad mini for mounting on a tripod with a standard 1/4"-20 screw on a tripod head. ...Designed with Fusion 360 Print Settings Printer Brand: RepRap ...
thingiverse
This Ipad Mini Holder is designed to fit with a otterbox defender case on it.
thingiverse
... adhesion. The threads are: 1/4" - 20 UNC for the tripod mount 1/2" - 13 UNC for the rest of the threading I had tap and die for these on hand in a good old Canadian Tire tap and die kit so that is what I went with, hopefully it is pretty common.
thingiverse
Fits an iPad Air 2 with a small case on it. ... Print Settings Printer Brand: Wanhao Printer: Wanhao Duplicator i3...
myminifactory
Desktop mount for iPAD with rugged case. print it with 4 parameters and 20% infill. Easy print no support require. If you want it more solid print it with 5 or 6 parameters. Update from FB user " I printed one actual size and the other at 60% for my...
thingiverse
Desktop mount for iPAD with rugged case. print it with 4 parameters and 20% infill. Easy print no support require. If you want it more solid print it with 5 or 6 parameters. Update from FB user " I printed one actual size and the other at 60% for...
thingiverse
A tripod mount for an iPad mini. ... Needs a 1/4" nut from a hardware store (mine was 3¢ from Lowe's).
thingiverse
I've had trouble finding a tripod mount that will hold it steady during long time-lapse photos. I constructed this holder, which fits the iPad while it's still in a ruggedized sleeve. ...The 1/2" nickel plated steel bar is tapped with a 1/4-20 thread...
thingiverse
Slide an Ipad mini in from the side and on the bottom there is a hole for the mount screw for a tripod. Position the tripod screw nice and straight the first time you place the screw so threads will form properly. PLA makes a nice mount filament for...
thingiverse
I bought on Amazon a mount for an iPad on a tripod and the 1/4" screw did not fit completely in the mount (not deep enough). ...I designed a disk with the right dimentions in order to ovecom this problem with success.
thingiverse
My spare tripod had a smaller mounting mechanism, the largest side of the square being around 31mm, then the smallest side 25mm This is a simple remix of the square type of mount made to be a bit smaller to fit these kinds of tripods. ...Mine is quite a...
youmagine
... use glue if the fit is not tight. The corners should be adjustable with friction,if you have any questions feel free to email me at sphetz@ymail.com or read more at my blog http://sphetz.blogspot.com/2015/02/3d-printed-adjustable-ipad-air.html#more
thingiverse
This is a way for you to attach your iPad to any 1/4-20 thread tripod. This version utilizes heat press inserts instead of bolts, its a more effective design however it uses parts less commonly available You'll need a few things to make this design...
grabcad
Model is ready for 3d printing and, will be good for only ipad 4s
prusaprinters
The easel can be printed standing up but the manfrotto mount needs supports under the mount plate.
thingiverse
The group wanted to adapt a Raspberry Pi with onboard camera case to a tripod. The cup holder approach was an easy way to do it. This thing was made with Tinkercad. ...Edit it online https://www.tinkercad.com/things/jDqMnplYtsN
thingiverse
Since I've been attending Zoom conferences very often since Corona, I needed a sturdy iPad holder. The iPad holder should also be easily adjustable. * In addition to the PLA parts, you need 3 x 30cm x 10mm (stainless steel, aluminum ...) pipe. *...