ipad clip for macbook 3d models

I needed a clamp to hold my iPad mini next to my macbook screen whilst working with multi screens. It is custom made to it fits my laptop with a cover on it. If you want to print this you may need to either scale it a bit or use some thin rubber as a...

I needed a clamp to hold my iPad mini next to my macbook screen whilst working with multi screens. It is custom made to it fits my laptop with a cover on it. If you want to print this you may need to either scale it a bit or use some thin rubber as a...

Stand for MacBook and iPad(Remix of https://www.thingiverse.com/thing:4736931)

This is a mount for my MacBook Pro 14" and my iPad 8. Gen. I use it as Sidecar Display. ... It is a little bit critical for the stability of the display, but it works...

In order to use iPad as a second screen, you should mount your iPad to the macbook screen.This gadget helps you a lot. It takes 50 mins to print. ... Please do not forget to give feedback.

If you are using SideCar or Duet Display with iPad, you might want to mount your iPad onto your MacBook. There are some tools to do that available in the market. This 3D printable object helps you achieve same thing. It has 2 hinges which allows...

Clip iPad cover for iPad air/pro

macbook/ipad/pancel holder

This is a small clip to fix the cable. ...Fits at Apple Macbook Power Adapter cable.

This is a headphone clip designed for hanging your headphones on a MacBook Pro when it is sitting vertical in a doc. This thing was made with Tinkercad. ...Edit it online https://www.tinkercad.com/things/0qpceVNtzoo

Made a clip for the charging cable of a MacBook. Got tired of the cable sliding off the table when the cable wasn't used. ... <strong>Fits this stand:</strong> https://www.thingiverse.com/thing:1330829

Hold your iPad Air or iPad mini on your MacBook Pro or Air for Apple Sidecar. The holders/hinges are easy and useful to improve productivity by using your iPad Air and mini as 2nd display. Applicable iPad: - iPad Air 3rd generation - support Apple...

It's very simple and measured 9mm (3/8Inch) width for the iPad slot and 17.5mm (11/16 Inch) width for the Macbook Air slot. Prints without supports obviously. Don't mind the slight warp on the left side in my pictures, I messed up the print with...

This is a simple clip we designed to attach the Sense 3D scanner to the back of a MacBook Air. When students scan objects, it's pretty cumbersome for one person to hold the scanner while another follows behind with the laptop, and even moreso when...

macbook/pancel/ipad Holder

An arch stand for both your macbook air and an iPad/iPhone. ...

This iPad holder clips onto a Novation Circuit groovebox and, as the name says, holds an iPad. ... Tested with a 6th generation (2018) iPad.

i-Pencil Clip for iPad Pro - I made this after receiving my iPad pro and i-Pencil and found there is no way to hold the Pencil to the iPad. This is made to fit a .600" thickness, iPad with cover. It fits snug and the Pencil pushes in very nicely...

A small but stable stand that fits both an iPad and a Macbook at the same time. ...No support required, infill I recommend it at 20% but you can use lower.

This is an arm holder for ipad mini, it is composed by: 1) an adjustable clip that can be attached to different types of surfaces (from 1cm to 3cm of thickness like desk, table or shelf), 2) an adjustable arm based on the ball socket joint, 3) a case...

Created for - Macbook Pro Retina 13“ (2012) - iPad Pro 12,9“ Gen. ...3

I was tired of my iPad and Macbook both being out on my desk, so I made this vertical stand to save some room.Supports are a bit of a pain to get off but it works.25% infill seems to be sturdy enough, could go higher if so inclined.

SummaryI made an easy place to keep my new Apple Pencil when I am not using it. ... Fits the iPad Pro with a case as pictured. ... Printed with PLA at 10% fill.

I made an easy place to keep my new Apple Pencil when I am not using it. ... Fits the iPad Pro with a case as pictured. ... Printed with PLA at 10% fill.

This is designed to be glued onto the iPad cover. Customise it - it holds my Adonit Jot Pro at 10mm diameter. ...Print Settings Printer Brand: RepRap ...

... Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=512350 Instructions Using the following options: _clip_angle = 100 _length = 200.0 _height = 24.0 _thickness = 3 _curvature = 100 _clip_radius = 2.5

... Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=512350 Instructions Using the following options: _length = 200.0 _curvature = 100 _height = 40.0 _clip_radius = 3.5 _thickness = 4 _clip_angle = 115

... Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=512350 Instructions Using the following options: _clip_angle = 110 _length = 241 _height = 20 _thickness = 3 _curvature = 89 _clip_radius = 2.5

This object has screws for tightening both iPad and MBP. it has small shape so that you can use as a keychain. ... Please do not forget to rotate the objects.

Clips on the top of a MacBook Air to allow for an Iphone to sit above the screen. ...Additionally, the clip can be used in an alternate position sitting on a flat surface.