ipad pro table stand 3d models

iPad Pro Stand

This model is based on KikiTay work in Thingiverse. ... https://www.thingiverse.com/thing:1241615 I just remodeled the stand to make it bigger for my iPad pro. ...I also added more notches and a place to put the Apple Pencil.

A stand for the Ipad or surface pro.

stand for ipad pro 11 and above  contain : complete stand part 1 and part 2   

It is a stand for iPad pro 2018 only. ... There are 4 different ways to stand.

130mm width iPad Pro stand works for either landscape and portrait handling. ... You can even put your iPad Pen at the rear.

A simple stand for an iPad Pro with silicone case - might work with other cases too. ... works upright and horizontally… :-)

Hello, This is my design of a stand for the new iPad Pro 2018. It will work with the 12.9” as well as the 11” version. Pictures show the 12.9” The angle is about 35 degrees and is perferct for working on a table. Cheers to all! ... ETH:...

This piece is a part for an Ipad Pro stand. ...Watch my Youtube video to see how to get a nut (M8) in.

An iPad Pro (11" & 12,9") stand ideal for your office desk. Photos taken with an 11" model.

SummaryI don't have a cover or keyboard or other stand for my new iPad Pro, so I designed this stand. It is fairly small so can easily bring in my backpack. Not designed for heavy tapping on the iPad. Can handle some soft tapping in portrait mode.

I've modified it so fit an iPad Pro.

I designed this stand for an iPad pro with a 60 degree inclination to suit me at work, however i noticed it fits several other tablets, try it and share your experience!

Split part stand for my 11" 2020 iPad Pro and 2nd gen apple pencil. Design was made split part because my printer cannot accommodate the whole part. ...Feel free to suppress the split feature to create a one part print.

Split part stand for my 11" 2020 iPad Pro and 2nd gen apple pencil. Design was made split part because my printer cannot accommodate the whole part. ...Feel free to suppress the split feature to create a one part print.

I designed this stand for an iPad pro with a 60 degree inclination to suit me at work, however i noticed it fits several other tablets, try it and share your experience!

This is a stand for iPad pro 12.9 inches. ... You can easily create one for your tablet by branching my onShape file: https://cad.onshape.com/documents/d1434b490c22972ff1559eb3/w/3bec4244b99e0c5721cccfa0/e/9b628b6557156b23244f0111

It also holds an iPad Pro (12") without problem. But not only Apple devices can be used; also other devices, as Samsung, Acer, Microsoft, Google, etc, can use this stand. The original design, of this tablet holder/-stand, contains an error. I had...

A simple stand for a 2018 iPad Pro. There are three different versions for different needs: stand_flat is the most basic version of the stand, it uses very little material and is easy to print, but it's a bit wobbly. stand_reinforced adds a bit of...

Just got an iPad Pro 11" 2019 - so i thought i need a cool stand... So here is it! This also works for 2018 Version and should work for the 12,9" Versions! ... It is very easy to print (no need for any support if printed in the correct orientation(...

iPad Pro 12.9 versiyonu için yaptım. Çok konforlu ve sağlam. ...

This is a stand for iPad pro 12.9 inches.You can easily create one for your tablet by branching my onShape file: https://cad.onshape.com/documents/d1434b490c22972ff1559eb3/w/3bec4244b99e0c5721cccfa0/e/9b628b6557156b23244f0111 

Stand to hold an iPad Pro while lying in bed on a pillow (in landscape at a 20 degree angle). After I designed and printed the part I discovered it needed to be a bit longer to avoid the iPad falling over (due to the fact that the mattress is not...

This thing was made with Tinkercad. ...Edit it online https://www.tinkercad.com/things/6twDynVPSo6 very simple two position iPad stand

... to your VESA level height for viewing pleasure. You don't have to peer around your Mac to see your iPad's screen, it is now all on one level! This stand fits all different sizes of iPads including the 12.9" - 1st Generation iPad (pictured here).

A simple holder for your iPad Pro 11. Tested with the 2018 model but might work with the new 2020. ...The sides are wide enough apart so the Apple Pencil still fits.</p>

A simple holder for your iPad Pro 11. Tested with the 2018 model but might work with the new 2020. ...The sides are wide enough apart so the Apple Pencil still fits between.

I recently bought an iPad Pro, but without a keyboard/smart-cover I lacked a way to prop it up when using it as a video-player. So I quickly whipped up a stand in Cinema4D. Print Settings Printer: Micro3D ...

Remix of GreaseMonkey88's Ipadpro stand. ... Ideal for reading. Increased base 'hooks' width to accommodate iPads with covers. Added additional organic struts for stability though the original works fine. Just thought it looks cooler. ...

This Thing is loosly inspired by > Galaxy Tab S6 Stand Multi Angle reforged to be able to accomodate a 1st Gen Ipad Pro with case. The design differs from that form PerditionFighter as it doesn't bring any angle indication but, as shown in the...