iphone 5 adapter 3d models
689799 3d models found related to iphone 5 adapter.thingiverse
I suggest sliding the assembled adapter up, manipulating the zoom, then sliding the assembled adapter back down until the eyepiece comes in contact with the top iPhone 5 adapter. More to come. Instructions I am able to make a fitting adapter...
thingiverse
I modified the Nexus 5 body and added an iPhone5-size cavity so I can use my iPhone in with this: http://www.thingiverse.com/thing:746299
grabcad
iphone 5 CasE adapter (from lightning pin to 30 pin adapter), iphone 5 case not only a casing but also an adapter,the lower portion of the casing is using the profile & thickness of iphone 4,thats the main purpose of this casing adapter is to use...
thingiverse
This is a Holder for the iPhone 5 which fits in to the car mount from TomTom. So you don't have to change the whole thing. ...You just have to print out the Adapter and bye a little converter for the plug.
thingiverse
Mount your iPhone 5 onto an existing camera tripod with this adapter. ... Update: I have edited the file slightly to so that the fit for the phone would not be so tight.
thingiverse
The adapter allows you to use your iPhone 5 to capture still images, video, or FaceTime content from under the microscope. Zoom and focus are provided by the microscope. The adapter is capable of adjusting to eye pieces that vary 30mm +/- 2mm. ...
thingiverse
I made a microscope adapter for my iPhone 5 out of laser-cut acrylic and double-sided tape. It's not perfect, but works well enough. The rubber feet are McMaster part #95495K68, and the acrylic is cut from 1/4" and 1/8" nominal thickness sheets. ...
thingiverse
A simple adapter to replace the old iphone dock connector in a Tesla Roadster 2.5.
thingiverse
With the iPhone 5 though I had to make an adapter. It is (on my replicator at least) perfectly sized to fit the Apple 30 pin to lightning adapter. Instructions This is not going to be useful for most people I imagine (how many of you that have 3d...
thingiverse
If you have an iPhone and want to make use of Google Cardboard (by Dodocase) then you'll have to use a #2 yellow pencil to raise up the device a bit and secure it with the provided rubber band. If you don't want that hassle, then print this adapter!
thingiverse
Added a ram tohttp://www.thingiverse.com/thing:215369 and blanked out the holes. Haven't tried it yet. Printing RAM first. I've used this holder just trim taped onto the dash of my truck. ... Works fine, but now I want it adjustable.
thingiverse
In addition to charging your phone it holds it in place during fast driving.
thingiverse
Take high resolution pictures with this Iphone 5 microscope eyepiece adapter.
thingiverse
With this accessory you can mount the iPhone 5 with any standard tripod , like any video camera or photo camera
thingiverse
Instructions This adapter is made to fit the iPhone 5 with a Lifeproof Fre case. The strap slots are sized to fit a 45mm neoprene armband I had from an older case. I printed the case on an Ultimaker with blue transulcent PLA. I used 25% fill and a...
thingiverse
It's for mounting an iPhone 5 on a Gorillapod. Instructions I printed it with the option to create a support under the overhanging parts. It came out nicely. The iPhone just fits in and doesn't fall...
thingiverse
... with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=55497 Instructions Using the following options: iphone_height = 123.9 iphone_width = 58.7 wall_thickness = 5 $fn = 50 adapter_height = 80 radius = 12 iphone_thick = 14.66
thingiverse
An adapter to use the iPhone 5 with iPhone 3G(S) car mounts. Instructions Parts required: 1x Part1.stl 4 x Part2.stl 1 x Part3.stl 4 x small woodscrew 1 x Apple Lightning to 30-pin adapter 20cm You might have to redrill the holes in Part3 depending...
grabcad
Its a rubber/silicone cover with a micro USB adapter. European Union have a new standard (2009) that all smartphones should have standard charges. ...Which uses a charger that outputs 5V at 500mA and a cable that terminates in a micro USB plug.
thingiverse
... Zeiss VR One Plus headset and my iPhone 5S barely fit. ... The adapter plate isn't the prettiest, but it gets the job done and works fine. VR is not the best on the iPhone 5S but it works and if the kids break the phone, I'm not going to be upset.
thingiverse
... johnr's didn't fit my Logitech dock. ... This'll hold a Lightning adapter while taking up a fairly small amount of footprint around it, yet offering some support to an iPhone 5 or other Lightning connector device above it, so it should fit in a dock.
thingiverse
This is an adapter for a 2014 Lexus SUV (LX570) so you can stand up your iPhone 5 in the compartment in your console made to fit an iPhone 4. You can stand it up in both portrait and landscape. Fits iPhone 5, 5s, and 5c. Just put in the phone...
prusaprinters
This is an adapter for a 2014 Lexus SUV (LX570) so you can stand up your iPhone 5 in the compartment in your console made to fit an iPhone 4. You can stand it up in both portrait and landscape. Fits iPhone 5, 5s, and 5c. ...Just put in the phone...
thingiverse
I needed a thicker slot for the iphone 5. The slot is 11.7mm and I shim it with tape to make sure the iphone is press fit. ... This is a remix of Patmik http://www.thingiverse.com/thing:55497
thingiverse
My Tinkercad Models:https://tinkercad.com/things/3CpgC90q2to-modified-telescope-mount-for-iphone-5-lamee-labs https://tinkercad.com/things/fkgAeBtuA1U-telescope-eyepiece-for-iphone-5-lamee-labs...
thingiverse
This thing was made with Tinkercad. ...Made this thing in 2 minutes for my endoscope. Fits super great. Worth 100$. Very satisfied :) Also made an iphone case a bit thicker because of glass screen protector on my iphone.
thingiverse
Apple sells an adapter for your dock's electronics, but I wanted something that would support my iPhone 5 a bit more securely. Instructions 1 - Get yourself an iPhone 5. 2 - Get one of Apple's Lightning Dock Adapters. 3 - Print one of these. 4 -...
thingiverse
Lens adapter to use Photojojo Iris lenses on an iPhone SE, iPhone 5s, or iPhone 5. These lenses are nice quality, with large, clear optics and machined aluminum housings. The product line was discontinued, and the only adapter available was for...
grabcad
I just received my adapter and have built this model to mimic the actual part. All dimensions have been taken with a calibrated set of callipers in inches. Enjoy! ... nano, ipod, touch, iphone
thingiverse
Developed at the LVPEI-MITRA Innovation Center to take Pictures through the iPhone 5 on the Haag-Streit BM900 Slit Lamp. ...Makers - Ganesh Babu & Dr.Anthony Vipin Das L V Prasad Eye Institute