iphone 5 phone holder for car 3d models
2718176 3d models found related to iphone 5 phone holder for car.cults3d
I 've printed it in PLA but it was deformed because of the heat of the sun in the car. So I printed it in ABS and now it is useful for my smartphone. ...You have to assemble both parts with cyanoacrylate glue
thingiverse
Designed a phone holder for my iPhone 7 Plus. Works with thin cover. Holder is suitable for air vent. Arm should be printed in 70% infill, other parts can be 20%. No need for glue or other thing. All parts are tight fit. If you encounter any...
thingiverse
holder I always was irritated when driving with my car and looking at the radio operating keys and did not see them. This lead into two eithers: Either I do not operate any button during the drive, Or I may run into risky situations when...
thingiverse
Phone 5 holder for VW Passat original phone mounting system. ...This is simple combination of these two designs: https://www.youmagine.com/designs/vw-phone-cradle-adapter-for-passat-3c-b5 andhttps://www.youmagine.com/designs/iphone-5c-dock Print...
thingiverse
This is a phone holder for your locker or anything magnetic! Place this in the desired location (must be magnetic) for clean and easy phone storage! Slide your phone in / out through the top for easy access. ...Note** Works best with an iPhone 5(c/s)...
youmagine
This is simple combination of these two designs:https://www.youmagine.com/designs/vw-phone-cradle-adapter-for-passat-3c-b5 andhttps://www.youmagine.com/designs/iphone-5c-dock
thingiverse
This is a Holder for the iPhone 5 which fits in to the car mount from TomTom. So you don't have to change the whole thing. ...You just have to print out the Adapter and bye a little converter for the plug.
thingiverse
Original didn't fit for my car. ...This one should.
thingiverse
Navigation in car with iPhone 5 but no Holder for it? ...Print one and stick it in your fan, works perfectly!
grabcad
iPhone 6 Car Phone Holder, designed for iPhone 6 standard size and a Toyota Corolla Dashboard.
thingiverse
... version of http://www.thingiverse.com/thing:526257 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=526257 Instructions Using the following options: iPhoneHeight = 59 iPhoneWidth = 125 iPhoneDepth = 8.5 slots = 2
thingiverse
... version of http://www.thingiverse.com/thing:526257 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=526257 Instructions Using the following options: iPhoneHeight = 59 iPhoneWidth = 125 slots = 2 iPhoneDepth = 8,5
thingiverse
This iPhone 5 (and his case) car holder plugs in your car CD player. You can access to command buttons and use a plug (even with adaptator) Un support pour iphone 5 (et sa coque) qui s'insert dans la fente du lecteur CD de votre voiture. Les...
thingiverse
... just the phone, or with cover/case. ...Just scale a bit up to fit the case. Print the mount 2 times, slide together to fit and us a 6 mm bolt to fasten. The holder can be mounted using 3mm hexoganal bolts Instructions Designed with sketchup 2014/2015
youmagine
Can be printed to fit just the phone, or with cover/case. ...Just scale a bit up to fit the case. Print the mount 2 times, slide together to fit and us a 6 mm bolt to fasten. The holder can be mounted using 3mm hexagonal bolts
pinshape
Mobile phone holder for cars that can be mounted in the air vent. Adjustable for different widths of phones (toothed design, from 2.25" to 3.5"). Tested with an iPhone 6s with different depth of cases (up to .5" thick). ...
cults3d
The design features 5 printable and snap-in pieces that together form a cell phone holder (based on the size of an IPhone 12 with ICase) that can be inserted into the CD slot of the car stereo. It has a joint adjusted by a nut that allows different...
thingiverse
This car mount is designed to hold an iPhone 11 with a case on. The added wedges are needed for some cd slots to give a tighter fit. ...One version is slanted a few degrees toward the driver.
cults3d
This car mount is designed to hold an iPhone 11 with a case on. The added wedges are needed for some cd slots to give a tighter fit. ...One version is slanted a few degrees toward the driver.
thingiverse
I designed this holder to compliment the Volvo phone clip here: https://www.thingiverse.com/thing:988170 The hole takes an M2 or M3 self-tap screw and screws direct on to the Volvo clip. The holder will accommodate the iPhone and a slim-ish case as...
thingiverse
It is iPhone 5 car holder. ... The shape of leg is adjusted for the dashboard of Kia Sportage R (2012)
thingiverse
Yet another iPhone 5/5s holder for your car. ...What makes this holder unique is that it's mounted to radiator with nylon ties.
thingiverse
A two part holder for iPhones in Lifeproof cases, I designed this holder so I can keep my iPhone in it's case and charge it on something.. I love the fact I can take my phone with me everywhere. including under water! I really dislike not being able...
thingiverse
This is car-holder for an iPhone 5/5s/SE that is being used with a protective cover. Typically such covers increase the volume of the phone, and hence the internal space is bigger than that of a "naked" phone to accommodate for that. The holder is...
cults3d
Phone holder for car (see photo). You can resize for different models of smartphones in the file "Phone_holder.f3d". ...Follow me Instagram https://www.instagram.com/serbul3d/
thingiverse
Phone holder for car (see photo). You can resize for different models of smartphones in the file "Phone_holder.f3d". ... Follow me Instagram https://www.instagram.com/serbul3d/
cults3d
phone holder for a car cup holder hole. notches of dovetail design adjusts for different phone widths. ... u need to print 2 arms.
prusaprinters
phone holder for a car cup holder hole. notches of dovetail design adjusts for different phone widths. u need to print 2 arms. Category: Mobile Phone
thingiverse
For your phone holder put a magnet in the hole and use it to hold your phone in the car Have Fun
pinshape
I have not designed a retainer plug for iPhone 5 and newer. I'll create one if anyone needs it. Instructions Print with 25% infill. If your printer is well tuned and can do bridges then it does not need support. ...If not print with support for the...