iphone 5 tripod mount 3d models
887091 3d models found related to iphone 5 tripod mount.thingiverse
Similar to a few other iPhone tripod mount options, my version features a hexagonal hole in the bottom, where an 11mm 20 TPI nut can be wedged/glued. The fit is pretty snug, so you may have to file it slightly to get the bolt to fit easily. The mount...
thingiverse
Customized version of http://www.thingiverse.com/thing:73622 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=73622 Instructions Using the following options:...
youmagine
Use a 1/4" nut in the middle for the proper tripod mount thread.Update: I just made a cut on the right side to the headphone port (you can use Volume + button on the headphone wire as a shutter button).
thingiverse
Iphone 5 tripod mount. Use a 1/4"-20 nut. Holds well by itself, but there are 2mm screw holes for #4 wood screws to use a rubber band or hair tie to ensure a strong connection. USE for $4 CASE on...
thingiverse
... with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=73622 Instructions Using the following options: holder_width = 10 base_inset = 3.5 base_height = 8.15 phone_width = 10.5 base_width = 35 holder_height = 20 base_cutout = .8
thingiverse
note: This is meant to replace the quick-release tripod mount, it will not screw into a tripod. Customized version of http://www.thingiverse.com/thing:73622 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=73622 ...
thingiverse
A replacement cleat for a Manfrotto 190XB tripod that holds an iPhone 5 both landscape or portrait. This thing was made with Tinkercad. Edit it online https://tinkercad.com/things/anAuTQQ6WJA ...
thingiverse
Edit it online https://tinkercad.com/things/eCL0lNEYJwk I remixed this from a couple of other designs in order to make a standard tripod mount that was simple, didn't need extra rubber bands and was big enough to fit my iPhone 5s with a bumper case...
cults3d
She asked me to find a way to connect her iPhone to our tripod allowing her to make the videos without holding the phone. Facebook Live videos are shot in portrait mode, but her iPhone 5S Otterbox case fits snug enough that it can be tilted to...
thingiverse
She asked me to find a way to connect her iPhone to our tripod allowing her to make the videos without holding the phone. Facebook Live videos are shot in portrait mode, but her iPhone 5S Otterbox case fits snug enough that it can be tilted to...
thingiverse
iPhone 6 fits loose so as not to scratch it when using the mount, while iPhone 5 fits rather tight. Works great for taking pictures, shooting videos or time lapses. You will need a M4 Nut to weld on the bottom and you are ready to go! ...Print Settings...
thingiverse
This is a iPhone 5/5s tripod mount designed for a Sunpak 7001 DX tripod with the quick release base. It may work with other tripods as is or with some adjustment. The phone snaps into the mount which locks into the tripod base with the quick...
thingiverse
Customized to fit a Vanguard tripod quick release. Customized version of http://www.thingiverse.com/thing:73622 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=73622 ...
thingiverse
I made this to mount my iPhone5 to the screw for a camera on my gorilla pod Print Settings Printer Brand: MakerBot Printer: MakerBot Replicator 2X Rafts: Yes Supports: No Resolution: low quality but 4 shells Infill: 10% Notes: I used 4 shells and it...
thingiverse
I measured my iPhone 5 together with its case and made a small holder to mount it on an Arca Swiss compatible head for timelapse recording. Case dimensions: 127x11 mm. ... I made a cut on the right side to the headphone port (you can use Volume + button...
thingiverse
A mount for Rllynch's Photoshpere Tripod Mount to fit my iPhone 5S with case. ...Get all the other parts required for the build from his thing page, here: https://www.thingiverse.com/thing:1739640
thingiverse
Remix of Thing: 55497 Changes: Modifed to fit iPhone 5 with Super Slim Case Modified mount for the Joby GorillaPod Mini Tripod. ... Added extra wall height Added HamilTek Gear Logo Instructions...
prusaprinters
A simple screw-on tripod mount for the iPhone 5/5S/SE (1st gen).Requires no screws/nuts to assemble. However, it is recommended to put a bit of foam on both sides, otherwise the phone will be quite loose while in the mount.I'd also recommend putting...
thingiverse
Mount your iPhone 5 onto an existing camera tripod with this adapter. ... Update: I have edited the file slightly to so that the fit for the phone would not be so tight.
thingiverse
... cut on the right side to the headphone port (you can use Volume + button on the headphone wire as a shutter button). https://www.youmagine.com/designs/dead-simple-iphone-5-tripod-mount Instructions I printed it with 0.1mm layer height, 20% infill.
thingiverse
Sized to be a snug fit for an iPhone 5 with front and scratch protectors. Works in both portrait and landscape orientations. ... You will need a 1/4"-20 bolt to attach the tripod foot to the part.
grabcad
Tripod Mount for iPhone or Digital Camera.I printed this several years ago when I needed a tripod mount for my iPhone 6.iPhone Camera Mount Website Post:https://ctmprojectsblog.wordpress.com/2016/07/23/3d-printed-iphone-tripod-mount/Original Digital...
thingiverse
A simple attachment for iPhone X and Xs to mount onto a standard camera tripod with screw thread. ...
prusaprinters
This design is a iPhone 6 + tripod mount for a camera stand Category: Mobile Phone
thingiverse
A simple 1/4-20 threaded tripod mount designed to hold an iPhone SE in a flexible case. ... The phone can be mounted horizontally or vertically.
thingiverse
A Tripod Mount for the iPhone 6. This thing was made with Tinkercad. ...Edit it online https://tinkercad.com/things/hsv4jgpnWCp Inspired by the Tripod Mount from haasebert (http://www.thingiverse.com/thing:25098)
thingiverse
An tripod mount i designed and created for my Hama Star 05 tripod. This fits right into the existing head. ... It probably works for phones other than the **iphone 6** as long as the **device width** does not exceed **68mm**
thingiverse
This lets me mount my iPhone (with Speck case attached) to my tripod for time-lapse photography. Instructions Update: Use the iPod_Tripod_Mount3 file - I shortened the legs and beefed up the frame on the bottom a bit to prevent breakage. I also...
thingiverse
I wanted a quick tripod mount for my iPhone. Absolutely did not want to have to use support or special settings. Designed to work with iphone 10 & 11. I want to note that I have seen a model that looks a bit like this somewhere. That's where I...