iphone 5s dash mount 3d models
382692 3d models found related to iphone 5s dash mount.thingiverse
A GoPro Mount for my iPhone 5s iPhone case. In order to create this, I measure my phones dimensions with my case, then pieced together small parts to fit a slidable mount into my phone. After that, I measured my gopro hero 4 and made an extension...
thingiverse
This mount works for an iPhone 5 or 5s with a thin case. 6.2mm 2.44" width. You can also use this mount without his case. A hole in the base allows you to connect the phone. You will find enclosed 2 stl files. One short mount and one middle...
thingiverse
... improvements on snap fit for phone and back fitment for vent. ...Holds the phone at a better angle to view while driving. A simple clip for your dash vents to hold a phone. This model is specific to VW GTI (2015+) - and Iphone 8Plus in Otterbox case.
thingiverse
After discovering Alfred (app to turn old phone into a IP camera) I designed this easy mount for the Iphone 5S. I printed it in 2 pieces; top and bottom. The 2 parts are connected by 2 M3, 10mm bolts. The connection to the frame is made with...
cults3d
just a mount i made for a friend that wanted to use his phone as a scanner.. ...holds a i phone 5s.
thingiverse
I used Chris Mcentee's (https://www.thingiverse.com/thing:2740465) iPhone 8+ car mount design for my own iPhone 8 car mount design to use in my 2018 Chevrolet Sonic. This is my first attempt at creating a 3D printable item. I used Tinkercad to...
thingiverse
just a mount i made for a friend that wanted to use his phone as a scanner.. holds a i phone 5s. ...Print Settings Printer Brand: MakerGear ...
thingiverse
iPhone 5 Tripod Adapter Similar to many other iphone tripod adapters, the advantages are that it fits an 11mm Hex Nut to facilitate repeated use. ... Print Settings Rafts: Yes ...
grabcad
iPhone 5S Case camera mount to print in order to use your phone as a GoPro
thingiverse
Want to mount your iPhone 5s on your bike? This one is the solution. Designed for a mountainbike steer with a diameter of 35-36 mm. ...Printable in one piece, no assembly needed, and very tight snap fit.
thingiverse
Designed to hold the iPhone 6 Plus in a louvered dash vent. ...Recommended that you increase the infill for greater strength.
thingiverse
GoPro mount case to fit iPhone 5/5s. Pretty basic design. Just allows you to mount a GoPro to the back of your phone case. Instructions I'd recommend printing on 100% fill if possible for strength.
youmagine
iPhone 5/5s version of this https://www.youmagine.com/designs/iphone-handlebar-mountphoto of it on bike is of the 4/4s version...
thingiverse
I designed this permanent Iphone 5S fixture, in order to reuse an old Iphone as control panels for my house automatisation. ... I used white ABS for printing.
thingiverse
EcoXGear makes a handlebar mount and a suction cup mount that lets you mount your iPhone 5 securely and adjust the angle. You can get them at West Marine and lots of other places for about $12. I have one for my bike handlebar so I can play...
thingiverse
This is a 2 piece mount for a iPhone 5 or iPhone 5s to use it as a security camera. I have several older iPhones laying around and they make good IP cameras. This bracket is 2 pieces. You can mount the first piece with screws, then slide the iphone...
thingiverse
... a 2 piece mount to put a magsafe charger in place of the airbag switch on a 95-04 Toyota Tacoma. ... Print the Magsafe piece laying down Print the dash clip piece on its side with supports. ...If you print it laying down the tabs will most likely break
thingiverse
I designed this phone mount so I could slide my iPhone 5s into the righthand side and back out for easy removal. There's a small hole at the bottom middle for the charger to go through. The top and bottom pieces are simply double sided taped (the...
thingiverse
Simple holder for holding iphone 5 (with case) that slots into the dashboard card holder (the little slot I think is for holding parking cards etc - on some, not all cars)... ... Instructions the tongue...
thingiverse
The designer of that mount tracked down a cheap ($4) lens from surplusshed.com that is suitable for iPhone macro photography. I wanted a mount that would slip over a case, and that I could print myself. This version takes the mount design from my...
myminifactory
The designer of that mount tracked down a cheap ($4) lens from surplusshed.com that is suitable for iPhone macro photography. I wanted a mount that would slip over a case, and that I could print myself. This version takes the mount design from my...
thingiverse
iPhone SE 5/5s Wandhalterung. Kann mit Case verwendet werden. ...
thingiverse
This is an iPhone 5/5s/SE case that allows you to mount your iPhone to the standard Gopro mount. ...Print Settings Rafts: No Supports: ...
thingiverse
This little piece enables you to use all your GoPro accessories with your iPhone 5 or 5s. As a plus you can also use it to mount your camera onto your iPhone. ...Print Settings Printer: M3D