iphone arm mount 3d models
441492 3d models found related to iphone arm mount.thingiverse
and the chinese articulated arm I bought on a well known gadget webshop was really crappy ... so I decided to make my own using an affordable metallic microphone arm. I agree this object is really customized to suit my bed headbord and the foldind...
thingiverse
Needed this for a commercial Backplates are 100x100mm with 3mm holes with countersink Beslag1 = backplate Beslag2 = long arm (150mm) Beslag3 = joint part Beslag4 = short arm (100mm) Each joint connecting is made for a M8 30mm bolt
thingiverse
Mount for mobile phone, avoiding visible screw holes. ...Works with Iphone 5, 6
thingiverse
phone mount specified for iphone 4s in a gorilla/survivor case and possibly other models??? ... may need to file down the tactical rail bars to fit.
thingiverse
I wanted a mount for my iphone in its case with that would allow me to rotate the phone around the axis of the camera. In the iphone, the camera is offset, so I added a mount there for the tripod. In addition, I wanted the frame to pivot horizontally...
thingiverse
So, if you want a mount that fits on your bed rail, and can wireless charge your phone, try this. The rail size is 3/4" and this should fit pretty snug, depending on how tight you have your settings dialed in. It could also be improved, so if...
thingiverse
Using 4 M3*8 screws, this mount fits 20mm(w) x 30mm(h) monitor arms and Microphone Arms with a 12mm Diameter base pole. ...I recommend to use a washer as well to prevent the arm from scraping against the top of the print.
prusaprinters
Using 4 M3*8 screws, this mount fits 20mm(w) x 30mm(h) monitor arms and Microphone Arms with a 12mm Diameter base pole. ...I recommend to use a washer as well to prevent the arm from scraping against the top of the print. Category: Audio
thingiverse
Universal arm mount that fits all arm sizes. ...Just uses a zip tie to mount on the arm.
thingiverse
This is a clip to route wire down a pole mount laptop or monitor arm.
thingiverse
A replacement part for the D12 chassis's lower arm mount for the independent front suspension.
thingiverse
Wife wanted to mount her single wand on the wall. ...Made a new mount arm to support.
thingiverse
If you have been using the setup based on what DSLR Video Shooter recommends in this video, maybe you will have problems mounting the microphone arm to the monitor arm. I printed this to have a rigid mount between the VESA monitor arm and the...
thingiverse
Suction mount for Robot Arm. Meant to be used with ftobler's robot arm : https://www.thingiverse.com/thing:1718984 and the Servo-Driven Suction Vacuum: https://www.thingiverse.com/thing:2861357 1. Run tube through clamp to suction cup below. 2.
thingiverse
I was looking for a really simple base design that worked with joochung's camera mount arm system so I whipped this up. ...Works better than I thought, even with a really long arm!
thingiverse
I made this to mount microphone arms to the wall to keep the desk less cluttered. Attach it to the wall with drywall screws or to a stud, then drop the arm in. ...The curved part should face the bottom.
thingiverse
I wanted to use this articulated arm to mount a camera onto. Since there were no remixes, I decided to design one myself. ...Hope this serves you well.
grabcad
This is an industrial robotic arm which can be mounted side ways typically to perform pick and place operations in large moving robots.
thingiverse
I was surprised to see that nobody had designed a microphone mount for this articulated arm system. Since there was none, I decided to design one to fit most common mic mounts. ...Simple design, but effective.