iphone car vent holder 3d models
468050 3d models found related to iphone car vent holder.thingiverse
Customized version of http://www.thingiverse.com/thing:526257 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=526257 Instructions Using the following options:...
prusaprinters
This is car mount for iPhone which use Apple's MagSafe charging. I designed the clip to fit the ac on my 2015 Volvo V60. Your experience with the clip may vary. ...The clip is off-center so that the phone is not in the way of the vent...
thingiverse
... with bumbers/cases and one for naked iPhones Works nice on my Volkswagen (Golf Mk6)! Print Settings Rafts: No Supports: Yes Resolution: 0.2mm Infill: 10% Post-Printing Pieces are put together with hot glue Just stick in (gently!) trough your vent
thingiverse
Phone holder to car vent. Optimized for iPhone 5/SE maybe you can use it with other phone models Hole for the charger. Apple logo. Only one piece to print. ...
thingiverse
... so that the phone can stay in the sleeve properly. I sized it for the iPhone XS with the otterbox case but should fit most iPhone XS with standard cases. This was also sized to a Toyota 4 Runner vent but should fit most standard vents. ...
thingiverse
I made this for my dad, because he didn't have anywhere to put his phone. ...It fits your phone with the case still on.
thingiverse
This is an iPhone holster for your car vent. You can insert your lightning cable into the custom slot so that your phone charges when holstered. The holster attaches to your car vent (or any other mounting surface) with ties straps in the holes...
pinshape
Mobile phone holder for cars that can be mounted in the air vent. Adjustable for different widths of phones (toothed design, from 2.25" to 3.5"). Tested with an iPhone 6s with different depth of cases (up to .5" thick). ...
thingiverse
The magnet in the MagSafe is surprisingly strong so my iPhone has never dropped off. Depending on where you live the inside of your car can get very hot in the middle of summer. ...Normal PLA can deform under heat exposure, so you will be better using...
thingiverse
Customized version of http://www.thingiverse.com/thing:526257 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=526257
thingiverse
Customized version of http://www.thingiverse.com/thing:1665478 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=1665478 Instructions Using the following options:...
thingiverse
Original design by nsverhagen. I only added length to the tendrils, to fit my wife's Mazda CX-7. ...Works perfectly, thanks nsverhagen!!
thingiverse
Vent mount cell phone holder. Fits iPhone SE with a slim case (12mm thick x 64 mm wide). Attaches to vents in car with zip ties. ...
thingiverse
iPhone MagSafe holder to car vent! You need a magnet to assembly completely This is my first upload, so maybe need some fix. ...All your comments are welcome
prusaprinters
I have designed this iPhone holder to be easily mounted on my car vent. It can be used as a stand. </p><p>The clip fits perfectly by sliding it from the front side. ...you need to parent two clips for stability. </p>
thingiverse
This file is based on a Toyota 4Runner's vent thickness. ... Adjust your print to match your car's vent thickness.
prusaprinters
Remix of Smart Phone holder for car vent by Walleye for easier printing. Allows for printing flat on print bed.</p><p>Prints in two parts, then superglue/adhere them together. ...I used supports for the overhands but not sure if that was...
thingiverse
This is a simple phone holder for the car. It hooks onto the vents. The vent hooks are attached to the back plate with 2mm wire (suspended ceiling wire from Home Depot.) The side hooks are work in progress. For now it is attached with zip ties. So...
thingiverse
I build holder for two cans on my volvo vent, because I could not find the good one.
thingiverse
This is a simple car phone holder suitable for iPhone 7 and Samsung A5 or other phones with similar width and thickness. Actually it could be easily adjusted by modifying the side support part. The original holder worked ok, but sat a bit too...
thingiverse
Made space for a charger, made sure the phone is more secure and doesn't fall forward at hard breaks. ...Added hooks for the rubber bands, so the pull completely horizontally. Also made the mount point smaller to fit the vents in my Saab 9-3.
thingiverse
... of http://www.thingiverse.com/thing:1448661 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=1448661 Instructions Using the following options: vent_fin_width = 3.2 length_of_fingers = 15 $fn = 100 inner_diameter = 18
thingiverse
A simple phone holder for phones with a thickness of up to 10mm and a width of 55mm to 120mm.
thingiverse
27.4.2019 you must forgot last version, now incoming ver.3 and two size holder diameter :-). Now it is without gaps and better hold in position after turn. Tested PLA , PETG ,ABS must working too .Enjoy it. 1.5.2016 Now...you must forgot all...
thingiverse
An iPhone 7 Plus vent holder for your car. Use zip ties to mount on the vent. Fits the iPhone 7 Plus well with the default case from Apple. Inspired by this design but designed from scratch. ... https://www.thingiverse.com/thing:2417931
thingiverse
iPhone car vent mount for MagSafe. It works pretty well on a BMW F10/F11, but probably many more cars. ...
thingiverse
Although there's tons of iPhone car holders in the market, for the life of me I could not find a decent one that mounts on the car vent. I also could not find any that mounted the phone in landscape at that location. I had a generic one for my...
thingiverse
It was made to hold an iPhone 6 plus with a casedazzle rugged case on it. Instructions Printed it solid so it's nice and sturdy. My first was on low resolution(300 micron) but came out awesome. ...May...