ipod gen 4 3d models
544889 3d models found related to ipod gen 4.thingiverse
This U clip allows a fourth generation iPod Shuffle to be attached 90 degrees to the direction of the Shuffle's own integral clip, eliminating the common situation where it winds up sideways (with the controls flipped accordingly).
grabcad
iPod Nano 6th Gen made using the technical drawings that Apple has released on their website.
thingiverse
This is a relatively accurate model of an iPod Gen 1 otherwise known as the Classic
pinshape
A simple iPod touch 5th gen stand that doesn't cost a lot of money from apple!
grabcad
... Sure, Apple continued the lineup , but constant comparisons to the iPhone eventually killed this off as well.So, here it is, back from the grave, the iPod Touch 4th Gen. ...( TSC edition )Like and comment on this post , and tell us what you think !
thingiverse
I wanted a wire manager for my iPod Nano 3G that would: (1) allow the wire to be coiled up for storage; (2) be attached to the iPod; (3) allow full use of the Nano, including access to all controls and ports, without disassembly -- this precluded...
thingiverse
I needed a holder for my old ipod and threw this design together quickly and it turned out pretty well. Its pretty easy to print at just about any resolution, I used 0.3, and then whatever your filament settings are. ...Hope it works for you!
thingiverse
Created a scale model of the Ipod Nano 7th generation device. I used to to make a small carrier for my vehicle. Side by side comparison photo added. Includes the two plugs under, power button above, and volume buttons on the side. ...Print Settings...
thingiverse
I wear some 3mm cord around my neck with some beads my son gave me in preschool, so now I can hang my iPod from them! As it prints its a pretty tight fit... If you enlarge it by one or two percent you may get better results. :) This thing was made...
grabcad
This was a project I did back in my Fall 2012 semester at Penn College. ...I simply reverse engineered my case for my IPod touch 2nd gen.
thingiverse
I couldn't find a case that I liked for my iPod, so I made my own. Designed for an iPod Video. I used a 60GB 5th gen. Tolerances are very tight in order to provide a snug fit. ...If you have issues with this, try printing at 101% or 102% scale.
cults3d
A minimal looking stand I designed for the iPod Nano 3rd gen so I can display it on my shelf. The size of the stand is 67.5mm * 45mm * 13mm h (37mm if you also count the standing piece), and the slot for the iPod is 53.5mm * 7.5 mm. So it could also...
cults3d
A minimal looking stand I designed for the iPod Video 5th gen 60GB (thick backplate) so I can display it on my shelf. The size of the stand is 76mm * 63mm * 13mm h (66.6mm if you also count the standing piece), and the slot for the iPod is 62.5mm *...
thingiverse
It's a sports case for a 1st gen ipod touch, you can add a wide rubberband on the back to wear it on your arm or the like. I've Included the freecad model if you want to modify it. ... Instructions Just...
thingiverse
This is a cover for an old Apple Ipod Shuffle (2nd generation).
thingiverse
Attach your iPod Nano 3G to many different holders with this cradle. ...I made it with standard mounting holes found on many different mounts, so mounting your iPod is very easy.
thingiverse
This is an iPod Nano 7th generation holder. Has rounded edges. ...Created with Inventor Fusion on a Mac.
sketchfab
This is an Ipod Model that I made while procrastinating on my Master’s Thesis. ...It turned out well so I thought I would upload it here!