ipod touch 2nd gen case 3d models

253619 3d models found related to ipod touch 2nd gen case.
IPod Touch 2nd Gen. Case
IPod Touch 2nd Gen. Case
grabcad

This was a project I did back in my Fall 2012 semester at Penn College. ...I simply reverse engineered my case for my IPod touch 2nd gen.

iPod Touch 2nd Gen "otter Box"
iPod Touch 2nd Gen "otter Box"
thingiverse

this is a case for the iPod 2nd Generation

Ipod touch 1st gen case
Ipod touch 1st gen case
thingiverse

It's a sports case for a 1st gen ipod touch, you can add a wide rubberband on the back to wear it on your arm or the like. I've Included the freecad model if you want to modify it. ... Instructions Just...

Ipod Touch 5th Gen case
Ipod Touch 5th Gen case
thingiverse

A case for an ipod.

Ipod Touch 5th Gen case
Ipod Touch 5th Gen case
cults3d

A case for an ipod.

ipod touch 5th gen case
ipod touch 5th gen case
thingiverse

I couldn't find a good fitting case that I could print with ninjaflex, so I made this for my girlfriends son. I printed with ninja flex (with supports) because the overhang is a bit much. Turned out great, nice snug fit. The camera area needs to...

Case for the 5th gen iPod Touch.
Case for the 5th gen iPod Touch.
grabcad

Clear silicone protective case for the 5th gen iPod Touch. ... iPod Touch is a registered trademark of the Apple company.

Apple iPod Touch 2nd generation case
Apple iPod Touch 2nd generation case
thingiverse

If you have any request on the design just ask me. For other phone cases check this. Here is the explanation of the files names: Flex: made for elastic filaments like TPU. Not tested.</li> <li><b>Rigid:</b> made for rigid (non-elastic) filaments...

iPod touch 5/6/7 Gen Case
iPod touch 5/6/7 Gen Case
thingiverse

Also, the original Thingiverse post by merms says "iPod Touch 5/6 case" but this was posted in 2018, before the iPod touch 7th gen was out, however they are the same size, so it should work fine with any iPod touch starting at the 5th gen and newer....

iPod touch 5/6/7 Gen Case
iPod touch 5/6/7 Gen Case
prusaprinters

It is also a great case to customize with your initials or a picture. Also, the original Thingiverse post by merms says "iPod Touch 5/6 case" but this was posted in 2018, before the iPod touch 7th gen was out, however they are the same size, so it...

Ipod Nano 2nd Gen
Ipod Nano 2nd Gen
grabcad

This is a 2GB 2nd gen iPod Nano

Companion Cube 4th Gen iPod Touch Case
Companion Cube 4th Gen iPod Touch Case
thingiverse

It's the Companion Cube on your iPod!

iPod Touch 4th Gen.
iPod Touch 4th Gen.
grabcad

... Sure, Apple continued the lineup , but constant comparisons to the iPhone eventually killed this off as well.So, here it is, back from the grave, the iPod Touch 4th Gen. ...( TSC edition )Like and comment on this post , and tell us what you think !

Apple ipod Shuffle 2nd gen
Apple ipod Shuffle 2nd gen
grabcad

3D model of apple ipod shuffle 2nd gen.

iPod nano 2nd gen stand
iPod nano 2nd gen stand
thingiverse

A stand for the iPod nano 2nd gen.

Brotherhood of Steel iPod Touch 4th Gen Case
Brotherhood of Steel iPod Touch 4th Gen Case
thingiverse

A Brotherhood of Steel case I made for the 4th gen iPod touch. NOTE: I use the MakerBot Replicator 2 and it gives the option to add supports to the structure to make it build-able, some 3D printers may not have this option, so take caution. ...The case...

Ipod Shuffle cover (2nd gen)
Ipod Shuffle cover (2nd gen)
thingiverse

This is a cover for an old Apple Ipod Shuffle (2nd generation).

Ipod Nano Holder (2nd Gen iPod Nano)
Ipod Nano Holder (2nd Gen iPod Nano)
thingiverse

I wear some 3mm cord around my neck with some beads my son gave me in preschool, so now I can hang my iPod from them! As it prints its a pretty tight fit... If you enlarge it by one or two percent you may get better results. :) This thing was made...

iPod Touch 5th Gen (Body for Case Design)
iPod Touch 5th Gen (Body for Case Design)
grabcad

I built this model from the Apple Specs as best as possible for case designs and visuals. Curvature may need to be adjusted upon release as no guides on plans. ...Built in Solidworks 2008.

Apple iPod Touch 5th Gen.
Apple iPod Touch 5th Gen.
grabcad

Scale model of the iPod touch 5th Gen. ...100% made from scratch.

Ipod nano  gen. case
Ipod nano gen. case
grabcad

Ipod nano gen.

iPod Touch gen 5 stand
iPod Touch gen 5 stand
thingiverse

Stand for iPod touch 5, mor or less for permanent placement. I use it at our home cinema for control of the cinema system (through Indigo home automation system). A calibrated printer is important, the iPod and cable (Apple original) is a tight fit.

Ipod touch case
Ipod touch case
thingiverse

case for 1st gen ipod touch. i have not tried this yet but it should work. ... Instructions print put together

iPod 1st - 2nd gen hold switch
iPod 1st - 2nd gen hold switch
thingiverse

The hold switch for the 1st and 2nd gen iPod.

Ipod Touch 4G case
Ipod Touch 4G case
thingiverse

Protect your Ipod Touch 4G with a 3D case. I did some improvements and repaired the STL file. Instructions Print the NEW repaired Case. Cleanup filaments around buttons. ...Snap you Touch into the case by sliding up from the bottom.

Wooden iPod Touch Case
Wooden iPod Touch Case
thingiverse

3D printed iPod touch bumper made out of wood.

iPod Touch Case
iPod Touch Case
thingiverse

My first ever 3D design. ...I also made a more interesting iPod touch case which I'll end up uploading to thingiverse soon. This thing was made with Tinkercad. ...Edit it online https://tinkercad.com/things/kuiPZbY87Gv

iPod 4th Gen Case
iPod 4th Gen Case
thingiverse

A case I made for a friend.

Ipod Nano 2nd Gen belt clip
Ipod Nano 2nd Gen belt clip
thingiverse

My wife wanted a IPod with a belt clip for fitness, so i designed this simple clip for my old IPod nano 2nd Gen. with FreeCAD. It sits very tight on the IPod, so it doesn't slip down. ...Happy wife, happy life ;-) The original idea is from this thing:...

Ipod touch in case
Ipod touch in case
thingiverse

... online for a few bucks but why buy when you can make. The IPod and case are actually two separate pieces but the STL merged them as one. ...I realize that this is not very helpful if anyone wants to make one so I'll post the pieces separately soon.