ir pen 3d models
45598 3d models found related to ir pen.thingiverse
Hi, today, i give you my Homemade IR Pen, for this, you just need: -Print the model -1 AA Battery -2 M3 Screws with nuts -1 VISHAY TSAL 6400 IR led -1 Temporary Switch -Some cable You can customize My IR pen and share it if you want. ... ...
thingiverse
Parametric IR pen for the wiimote (http://johnnylee.net/projects/wii/)
thingiverse
Customized version of http://www.thingiverse.com/thing:273099 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=273099 Instructions Using the following options: basey =...
thingiverse
Customized version of https://www.thingiverse.com/thing:749887 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=749887
grabcad
Concept of a IR Photocell Rhinoceros 4 Fryrender https://www.facebook.com/acd.design
thingiverse
IR Dome for 4 IR LED's, IR Receiver, LED RGB ring, Arduino mini, radio TX and PSU, primary as mySensors device. But can be customized for whatever... ...:) PSU: HLK-5M05 LED Ring dimension: 35.5 x 50mm (35x52) (i use ring with 12 x WS2812B LED's) IR...
grabcad
IR DIRECTFET IRF6691 STEP model for Altium Designer visualization. ...X=90 Y=0 Z=90 Offset=0Mils.
thingiverse
This one i use with a 16x60mm 850 nm focusable laser on 160mw and that one is much moore efficiant then the stock ir that comes with the 410 , i dont know how strong laser you can use but between 160 and 250 would probably go , 160mw is what i am...
thingiverse
Insert LEDs top first from the back and the detector face first from the back of the pod.(you may need to remove metal case that most TSOP IR detectors have) You may want to use a small amount of glue to keep the detector snug only after you have...
prusaprinters
I designed this 940nm LED lamp for my NIR (near IR) photography projects /hobby.The IR emiter consists of 7 3W-LEDS. For main power supply an 250W DC-DC Step-Up converter with CC and CV regulation is used. ...The other, smaller DC-DC is for...
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=749887 Instructions Using the following options: basethickness_percent = 0.1 base_radius_add_percent = .1 fontname = Holtwood One SC textsize = 25 RoundedBase = 1 shift_font_percent = 0.07...
thingiverse
... to monitor the actual speed of my DC CNC spindle, so I made this tachometer. ...It has a contactless reflective IR sensor. Simply glue a piece of reflective aluminum foil on your spindle's fan to make the sensor work. ... https://youtu.be/Nwz5lS-U4uI
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=714444 Instructions Using the following options: basethickness_percent = 0.1 textsize = 16 shift_font_percent = 0.07 baseheight_percent = .33 textheight = 10 fontfilename = write/orbitron.dxf...
thingiverse
... ...Its a fantastic little board which runs great of AAA batteries. AnalysIR make a whole range of fantastic range of high quality IR boards ready to run on Arduino, ESP8266, Photon and even RaspPi. ...------> Check them out at https://www.analysir.com
thingiverse
Download Arduino IDE (https://www.arduino.cc/en/main/software) Install IRLib2 (https://github.com/cyborg5/IRLib2) Upload "record.ino" sketch from IRLib2 examples Open Serial Monitor view in Arduino IDE Push buttons on your IR remote and watch serial...
thingiverse
# IR-Scanner: A simple device to read codes from IR remote and output them to a small screen. This is a basic Arduino-powered device to quickly decode signals from infrared remote controls so that you can better understand how different devices...
thingiverse
This is an adjustable bracket to hold an IR LED and it's paired IR Photodiode to create a sensor assembly for a reflective optical tachometer. Here's the Instructable on how to create the full tachometer ...
grabcad
Emetteur IR grove.La position de la LED IR est approximative.