irrigation spikes 3d models
7606 3d models found related to irrigation spikes.thingiverse
Spikes for holding 1/4 inch Mr Mister drip irrigation tubing hoses.
youmagine
This version of my drip irrigation spike has the same snap clip for 1/4" tubing but features a side snap clip to directly hold irrigation emitters with 1/4" barb outlets.
youmagine
Multi-purpose drip irrigation spike. Upper clip securely holds standard 1/4" tubing. Lower port fits smaller size emitter outlets and provides a drip lip for efficient transfer to the soil below. ... Use the lower port to hold an emitter and the clip...
thingiverse
This is a custom garden irrigation system spike to clamp a microjet pipe without using the microjet nozzle at the end. This was specifically created for my custom drip irrigation using greywater, which is likely to clog nozzles in the standard...
pinshape
Which might explain why the "irrigation" lasted almost a week. However, this can be easily fixed by slightly cutting off the tip with an X-ACTO. In my opinion, it's better that it lasts longer, than shorter. But not too long of course! All other side...
thingiverse
Which might explain why the "irrigation" lasted almost a week. However, this can be easily fixed by slightly cutting off the tip with an X-ACTO. In my opinion, it's better that it lasts longer, than shorter. But not too long of course! All other side...
thingiverse
I needed a plant spike-type dripper that delivers the nutrient solution below the surface but near the top. This works with approx. 0.170 ID tubing. It is about 3 inches long and the hole goes through both sides. The internal cavities are diamond...
thingiverse
Irrigation drip line spike. Great for 1/4" or smaller line that waters a tomato plant for example. ...
thingiverse
This is the watering spike I use for my solar powered ESP32 automated irrigation system. It is designed to work with 5/16" or 8mm tubing and a small DC water pump. It provides even water distribution across many spikes. Single line or in a loop. ...
thingiverse
Customized version of https://www.thingiverse.com/thing:3641975 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3641975
thingiverse
Spikes/Horns for cosplay or decoration. ...multiple sizes for whatever your needs If you wanna support more 3d projects tips can go to $printablez (cashapp)
sketchfab
These are a smaller set of spikes that I made for my teams game in our game prototyping class at the Art Institute of Atlanta
cults3d
Spikes/Horns for cosplay or decoration. ...multiple sizes for whatever your needs If you wanna support more 3d projects tips can go to $printablez (cashapp)
thingiverse
Drip irrigation system component. ...https://youtu.be/PHNedNbQr4w kap_1.stl - 3-3.5mm kap_2.stl 4.5-4.8mm
thingiverse
Just a quick irrigation spout i made to fit my automated garden setup. ...I included the fusion 360 file as well.
thingiverse
My irrigation system is the standard above-ground quarter-inch tubing that connects up to sprayers, drip feeds, and drop hoses—the sort of thing you find in most garden stores. I discovered I needed a few more hose stakes to keep things tidy and...
thingiverse
This is to reach over a sidewalk and water plants from a drip irrigation system. Enlarge holes with a drill if needed and then "cold form" the threads using a SS bolt, friction melts the plastic and this produces stronger threads. Cut the ball (see...
thingiverse
This tiny item fits snugly into the end of 1/4" irrigation tubing, and splits the stream in two. My intent was to reduce the speed of the water as it exited, and also spread out the area where water is directed. It prints with the holes at the top,...