isopropyl alcohol dispenser 3d models

I designed a box for the alcohol pads that I use to clean my print bed. Print instructionsCategory: 3D Printer Accessories Print Settings Printer Brand: Creality Printer: CR-10 Rafts: No Supports: No Resolution: 0.2 Infill: 20%

<p>This is a tower to hold a pump bottle for IPA and cotton rounds. It can hold a bottle roughly 60mm round and 120mm tall. I use them to clean my build plate.</p> <h3>Print instructions</h3><p>There is a separate top and bottom to print then...

If you want this model contact me at stefanot30@gmail.com. ...thanks

This just mounts my build plate cleaning materials on the wall right next to my 3d printer. ... Hope you enjoy it!

Wall mount for hydro-alcohol dispenser. For 70 mm diameter and more than 130 mm high dispenser. With window to see the level. Soporte de pared para dispensador de hidroalcohol. Para dispensador de 70mm de diámetro y más de 130mm de alto. ... Con...

Made this to hold alcohol swab for bed wipe down. ...Uses M5x8 + tnut Holds up to 13 BD alcohol swabs

for 50 (~55)mm disposable alcohol pads. Print instructionsThere are small tabs at the edges of the overhang where the pads are pulled out. you will need to clean this area up with a knife. ... pads are designed to come out and down at a 15 degree angle...

I created the dispenser in two parts because I didn't want to mess with supports inside that thin slot. So the hopper has a ridge that slides into the groove on the base, and locks in place with a snap. No glue or anything needed. ...Then I added a cap...

I created the dispenser in two parts because I didn't want to mess with supports inside that thin slot. So the hopper has a ridge that slides into the groove on the base, and locks in place with a snap. No glue or anything needed. ...Then I added a cap...

– Hand Sanitizer Gel Alcohol Dispenser 4K PBR –

<p>A threaded screw-on cap for the 5-gallon isopropanol drum from McMaster-Carr. ...A rough FreeCAD model of the neck in available as well.</p>

<p>A threaded screw-on spout for the 5-gallon isopropanol drum from McMaster-Carr. Several spout designs available. ...Still in testing.</p>

Based on the beautiful design by Tantalus. I made mine a bit longer and added the chemical formula to the side. ... Will hold about 80-100 pads.

View videos here: https://www.youtube.com/watch?v=lM6uJ98DDV4

all link and priew in youtube https://youtu.be/xwffzTF0WCo

https://youtu.be/xwffzTF0WCo

adapter for milkbottle to sprayer or alcohol dispenser

adapter for Australian milk bottle cap thread and alcohol sanitiser dispenser.

Aus milk bottle cap thread and spray bottle or alcohol dispenser adapter

For everyone who don't like the hard to open Safety Cap on Isopropyl Alcohol Bottles. It requires only one turn to open but still sits securely on the bottle. ... Chances are, your bottle has the same thread as mine, so go try it out!

I created this model for my friend who works as a barman. Also - I decided to share the model for you. For personal use. ... If you want to support me: The best way to say "thank you" is to send a dollar (or more) Alas, I can't accept Paypal, but I...

Where to store the cleaning alcohol for the print beds? The bottle holder keeps it in a safe place. Designed with FreeCAD v0.16. Source files included. ...Feel free to modify it to your needs.

A pegboard holder for a 16oz (473ml) rectangular bottle of isopropyl alcohol and some q-tips.

Alcohol container.

Alcohol stencil

porta alcohol

Alcohol bottle.

Alcohol distiller

alcohol_sprayer