j head hotend 3d models
164542 3d models found related to j head hotend.grabcad
Model of an Aliexpress J-head hotend for 3D printing.Good for mockups, designing tool heads, holders and more, for printer model/carriage build etc.
pinshape
J head hotend mounting bracket layer 0.3mm print speed 30mm/sec
cults3d
An adapter to mount a J-Head V6 hotend to my K8200 (printed with Anycubic because K8200 was no longer usable / parts of the old hotend where melted).
thingiverse
An adapter to mount a J-Head V6 hotend to my K8200 (printed with Anycubic because K8200 was no longer usable / parts of the old hotend where melted).
thingiverse
Mounting Kit for a J-Head hotend extruder for my "China" Prusa i3 .. ...Have to buy one of these:http://www.ebay.com/itm/291588669433?_trksid=p2060353.m2749.l2649&var=590631719814&ssPageName=STRK%3AMEBIDX%3AIT Print Settings Printer Brand: ...
pinshape
SummaryMounting Kit for a J-Head hotend extruder for my "China" Prusa i3 .. ...Have to buy one of these: http://www.ebay.com/itm/291588669433?_trksid=p2060353.m2749.l2649&var=590631719814&ssPageName=STRK%3AMEBIDX%3AITPrint SettingsPrinter Brand:...
thingiverse
This duct is used to cool the filament running trough the hotend. (diameter 24,5mm) It is suitable to fit with any 40x40 axial fan using M3 screws. ... The total height of the channel is 40mm (without supports on top and bottom is 31mm).
thingiverse
A mount for a J-head V6 Hotend that can be found here. This was designed for a Prusia i3 but it should work with most printers. ...Print Settings Printer Brand: RepRap ...
prusaprinters
Fan Shroud for 40mm fan on a V5 J-head Hotend (commonly used in the Anycubic Mega series) to replace the metal hotend housing. ...By that airflow is improved and the weight of the whole printhead ist reduced.Attention:You can only remove the housing...
thingiverse
I've attempted to adjust the MakerGear M2 filament drive to fit a J-Head hotend. I've not tested this yet, but thought I'd share anyway. MakerGear hotends and J-Head hotends are a bit different. The push fit section diameters are 16.5mm and 12.5mm...
thingiverse
I have a Zonestar P802Q, fitted with chinese J-Head hotend. I had problems printing PLA, after a few hours it jammed always.. No problems with ABS, though! But I figured PLA problem must be because of inadequate cooling, because the whole heat sink...
thingiverse
... of the mount to make the height of the section that inserts into the hot-end groove match the Micron3DP hot-end. This is a link to the hot-end:http://micron3dp.myshopify.com/collections/hot-ends/products/all-metal-j-head-compatible-1-75-mm-hot-end
thingiverse
Also usable for other Printers or Hotends
thingiverse
... fan. ...Couldn't find one I liked, so built my own. Took far to long building this in sketchup, Just painful. But got there. The fan holder diverts 20% of the air from the fan, to cools down the print, without cooling down the hotend itself. ...
thingiverse
The new E3D-v6 works far better, the only problem is that you are going to lose some Z height because the hotend height is greater than the original one. But it's possible to design a new mount in consequence. You will have to drill holes yourself...
thingiverse
Enlarged clearance for skate bearing - spins freely now, no binding Thickened section for thread insert for tension screw Added addition structural supports to stiffen-up mount for stepper and for hotend. Minor work remaining: -re-work fan mount...
thingiverse
Added holes for standard pursa x-carriages. ... Press Fit by@Exzile works nicely, no screw on cover necessary.
thingiverse
This part is an extension to the single fan version for use with an additional radial fan. The job of the radial fan is to cool down the filament right after printing, which will improve the printers quality. I design that part as i need a very...
thingiverse
This part is inspirited from http://www.thingiverse.com/thing:33889.
thingiverse
40mm fan air duct for Geeetech All Metal J-head hotend It works! ...Use it =) Added fixed model, for better ptinting.
thingiverse
# MK8 Carriage on 3D printer under MK8 + V5 J head hotend. Carriage on 3D printer under MK8 + V5 J head hotel on printer D(re/J) Bot (in plastic testing) # Flex - does not wind on the gear.... perfectly #PLA-excellent #ABS - excellent #The nylon -...
grabcad
My old hotend holder of my self build look alike Ultimaker 2+ was not so good, and worn out, so I bought a new hotend, a J-Head CR10 Hotend Extruder, and designed a new holder for it.It fits very well and is stable so I am very pleased with the...
thingiverse
Dual extrusion carriage for Repemaker 3d printer. ...For j-head hotend. ...A update for Repemaker 3d printer http://www.thingiverse.com/thing:138063 Here you can view the new version (not update yet)http://www.youtube.com/watch?v=OfbQ5YGW0K4
thingiverse
Cooling for Filament and Hotend. ... Also usable for other Printers or Hotends.
thingiverse
the sensor is directly behind the hotend 20.575mm is the exact Y offset (from the center of the jhead nozzle to the center of the proximity sensor) there is also an end clamp for use with a 25x25mm fan for the Hexagon all metal hotend, will probably...
thingiverse
... place the nuts in the back and glue a 40 mm fan to the back. I keep a distance of 15mm to the heating block as described in the manual for BL Touch. and approximately 1.8 mm over the Nozzle. I have attached pdf with dimensions of the Hotend I use
thingiverse
Firstly I wanted to have hotend closer to X carriage to extend my Y axis range. Secondly I saw some issues from part being cooled only from one side and different shapes of fan duct did not help so I designed double blower version. I tried also to...
thingiverse
this design is used to mount the cheap V5 bowden hotend available on aliexpress with 24 mm cooling fan...
thingiverse
mod for reprap. ...Still beta files might change