jacob hub motor 3d models
102039 3d models found related to jacob hub motor.grabcad
Nubs to help the wheel slipping issue on Jacob's Hub motors. Just put them on and use some duct tape to hold them in place. ...The slot is there in case someone wants to glue them on with epoxy to give a larger surface area.
thingiverse
... to the hub motor wheel slip dilema. ...https://www.electric-skateboard.builders/t/emf-jacob-hub-motor-polyurethane-development/20042/47 Knubs for preventing slip on the 83mm brushless hub motor. ...Print in something than can resist temps upto 170F
grabcad
An electric hub motor with threaded shaft on one side.The hub itself acts as a ratchet for freewheel.The model was created with Solid Edge.
grabcad
A hub motor named Pablo.I intended to fabricate this motor, but, since the laminations were not off-the-shelf, it would have been very expensive.
thingiverse
Customized version of http://www.thingiverse.com/thing:340321 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=340321 Instructions Using the following options: BlockWidth = 2 Name = JACOB BlockLength = 10
thingiverse
... version of http://www.thingiverse.com/thing:45576 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=45576 Instructions Using the following options: font_spacing = 1 word = JACOB J. ...pen_length = 130 font_scale = 2.1
thingiverse
Customized version of http://www.thingiverse.com/thing:340321 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=340321 Instructions Using the following options: BlockLength = 10 Name = JACOB BlockWidth = 2
thingiverse
... version of http://www.thingiverse.com/thing:45576 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=45576 Instructions Using the following options: word = JACOB J. ...font_scale = 2.1 font_spacing = 1 pen_length = 130
thingiverse
Customized version of http://www.thingiverse.com/thing:340321 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=340321 Instructions Using the following options: BlockWidth = 2 Name = JACOB BlockLength = 4
thingiverse
Customized version of http://www.thingiverse.com/thing:340321 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=340321 Instructions Using the following options: BlockWidth = 2 Name = JACOB BlockLength = 6
thingiverse
Customized version of http://www.thingiverse.com/thing:676537 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=676537 Instructions Using the following options: keychain_loop = Yes text = JACOB text_style = 0
thingiverse
Connects NXT motor hubs to Tetrix pieces with the help of some bolts and a lego axle Also check out my blog
thingiverse
Used on a FIRST Robotics window motor hub to hold a 1/2" thinwall aluminum tubing. Print 2. ...Top and Bottom.
thingiverse
The gears in the hub motor will eventually break. ...this is a replacement part because these gears are not sold any more.
cults3d
The gears in the hub motor will eventually break. ...this is a replacement part because these gears are not sold any more.
thingiverse
... ...http://www.thingiverse.com/apps/customizer/run?thing_id=52734 Instructions Using the following options: stick_thickness = 3 font_thickness = 5 message = Jacob font_size = 15 Font = write/orbitron.dxf stick_width = 8 hole_radius = 3 flat_bottom = 1
thingiverse
... ...http://www.thingiverse.com/apps/customizer/run?thing_id=52734 Instructions Using the following options: font_size = 15 flat_bottom = 1 Font = write/orbitron.dxf message = Jacob hole_radius = 3 stick_thickness = 3 stick_width = 8 font_thickness = 5
thingiverse
... Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=56257 Instructions Using the following options: inner_radius = 28 nozzlediam = 0.4 text = JACOB outer_radius = 33 sections = 21 length = 15 text_thickness = 4
thingiverse
... ...http://www.thingiverse.com/apps/customizer/run?thing_id=52734 Instructions Using the following options: flat_bottom = 1 hole_radius = 3 Font = write/orbitron.dxf font_thickness = 5 font_size = 10 stick_width = 8 stick_thickness = 3 message = Jacob
thingiverse
... Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=40704 Instructions Using the following options: message = Jacob Soles font_size = 10 ring_thickness = 1.6 ring_size = 18.14 font_spacing = 0 Font = write/Letters.dxf ring_width = 6
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=191198 Instructions Using the following options: text_string = Jacob text_font = write/orbitron.dxf text_direction = 1 text_vertical_offset = 0 text_horizontal_offset = 8 text_height = 12...