jansjo lamp 3d models
59164 3d models found related to jansjo lamp.thingiverse
This shade is meant to slip onto the Ikea Jansjo lamp. The LED lens would shine in my eyes when I positioned it for work. (This is typical with most LED desk lamps I've used.) Since I've started using this, I've notice that my eye fatigue is...
thingiverse
The Ikea LED lamp was shining in my eye, so I made a shade. ...It has a slot in it to use a tie wrap to hold it to the lamp and allow it to spin/adjust of to any angle.
thingiverse
***EDIT: WRONG TABLE NAME IN STL FILE*** ***THIS IS FOR A LINNMON TABLE*** I made this to be able to attach a Jansjo lamp to a Linnmon table. ...
thingiverse
A little soldering help attached to an IKEA Jansjo lamp. Alligator clips soldered on the ands of 2x24cm twisted copper wire (1.3mm/16AWG). You will need a 16x2mm screw and nut for securing to the lamp and another four of same scews or similar...
thingiverse
Print Settings Printer: QIDI Rafts: No Supports: No Resolution: 0.3 Infill: 50% Notes: Printed with MG PLA at 210C/60C, 50% fill, 7 top,7 bottom, 4 outside Post-Printing Installation Depending upon the orientation in which you decide to use this...
thingiverse
This is a bracket to mount an IKEA Jansjo LED Lamp to Skadis pegboard. The IKEA lamp is [https://www.ikea.com/us/en/catalog/products/50386066/] Fusion 360 files are included for you personalization pleasure... It's an example of using the my...
thingiverse
It's a clamp on 30mm shaft for IKEA's Jansjo LED lamp. Print Settings Printer Brand: RepRap Printer: Prusa I3 ...
thingiverse
Just a remix for older jansjo with the clip for base. just screw the light and you are done! ... original file https://www.thingiverse.com/thing:3734958
thingiverse
This mod allows you to attach the lamp stalk directly to your printer without using the big heavy round base it comes with. Print with flat side down, recommend PETG/abs with 15% gyroid infill for strength. ... You will need M5 8mm screws and t-nuts...
thingiverse
Use two M3 20mm screws and two nuts, two alligator clips with strong aluminium wire (4mm with isolation) to transform IKEA Janso LED lamp to third hands (helping hands) soldering station. ...http://www.ikea.com/us/en/catalog/products/20169658/
youmagine
Suggested position is to keep the lens on the inward side of the lamp (between head and base/mount) to avoid extraneous weight on the flexible shaft. It is very stable and balanced this way. Print Settings Printer: FLUX Delta Rafts: No Supports: No...
prusaprinters
This mod allows you to attach the lamp stalk directly to your printer without using the big heavy round base it comes with. Tested and works with my Mk2.5s full bear frame. Print with flat side down, recommend PETG/abs with 15% gyroid infill for...
myminifactory
Replacement part for IKEA JANSJÖ lamp (old version)
thingiverse
Replacement part for IKEA JANSJÖ lamp (old version) Upper part is avaible here: https://www.thingiverse.com/thing:3151087 Print Settings Notes: set minimal infill lenght on 3mm or less for good ring infill
thingiverse
Let's you mount a Jansjo gooseneck spot lamp from Ikea on 1.5" 8020 aluminum extrusion. Simply snaps into the slot in the rail. Can be mounted horizontally or vertically. Yes, it hangs on that tightly! ...
thingiverse
It is a mount for clamping IKEA JANSJÖ lamp on Dell p2414h moitor. It should also work for other Dell monitor with similar back panel. ... To install, just slide it on the top of monitor, the little tenon should grab the venting hole of monitor.
thingiverse
Ikea's Jansjo lamps are fantastic task lights but they're glary. These hide the light source from most angles and attach with a 1-1/8" diameter "ranger band". Print in Proto-Pasta carbon-filled PLA for an optically black, matte finish. Also, note...
myminifactory
This is a cable clip to attach Raspberry Pi camera ribbon cable to the neck of an IKEA JANSJÖ LED lamp. ...I used this in combination with Raspberry Pi Camera Bracket For IKEA JANSJO LED Lamp.
thingiverse
I used this in combination with [Raspberry Pi Camera Bracket For IKEA JANSJO LED Lamp](https://www.thingiverse.com/thing:3122247) and [Raspberry Pi 2B Case For IKEA JANSJO LED Lamp](https://www.thingiverse.com/thing:3333716). ... Design files on...
thingiverse
File Jansjo_ribbon_clasp.stl is a part that clips onto the gooseneck part of the Jansjo lamp for routing the picam ribbon cable along the gooseneck. I also have a custom mounting base for the Jansjo lamp. ... See Stylish Mounting Base for IKEA Jansjo...
thingiverse
Support de lampe Jansjö (Ikea) pour SmartCub3D Matériel nécessaire: x1 Lampe Ikea modèle Jansjö (avec socle) Lame de cutter (pour retirer la couche de construction au niveau des têtes de vis noyées) Une vis M5 x 20mm (type CHC pour l'exemple) +...
myminifactory
I am using it in combination with [Raspberry Pi Camera Cable Bracket For IKEA JANSJO LED Lamp](https://www.myminifactory.com/object/3d-print-raspberry-pi-camera-cable-bracket-for-ikea-jansjo-led-lamp-82975) and [Raspberry Pi Camera Bracket For IKEA...
thingiverse
I am using it in combination with [Raspberry Pi Camera Cable Bracket For IKEA JANSJO LED Lamp](https://www.thingiverse.com/thing:3333690) and [Raspberry Pi Camera Bracket For IKEA JANSJO LED Lamp](https://www.thingiverse.com/thing:3122247). While my...
thingiverse
This is used to mount a Raspberry Pi camera to an IKEA JANSJO LED desk lamp. ... https://www.ikea.com/us/en/catalog/products/00385941/ It's a tight fit so the M3x16mm screw with matching M3 nut is not technically required.
thingiverse
lamp: http://www.ikea.com/us/en/catalog/products/20169658/ Instructions Take the base off the lamp and keep the screws. Insert the goose-neck base into the printed clip and screw it down using the original screws. Push the clip down into the end of...
thingiverse
The bracket called CNR6400-B is intended to mount the in-cable switch of an IKEA Jansjo lamp to the power supply box of an Ender-3 printer. The objective is to keep the switch in a position to operate it easily and to keep the lamp cables out of the...
thingiverse
This is a Merge of these 2 designs I chose to print it face down and create supports for the LED bracket portion. ... https://www.thingiverse.com/thing:3122247 https://www.thingiverse.com/thing:3114849
thingiverse
... usb port on the side of my CR-10 Smart is useless. ... It is then perfect to power this little light from ikea ( https://www.ikea.com/ca/en/p/jansjoe-led-usb-lamp-black-70291232/ ) I used a bit longer 3mm (M3 x6) screws to replace the original ones.
3docean
Ikea Jansjo Led Work Lamp Created and Rendered With Blender Features: -5 Different Format: blender(deafult), dae, 3ds, obj, fbx -Scene and Node Included in Blender -UV Unwrapped -Low Poly Game Ready