jigsaw blade holder 3d models

Jigsaw blade holder, printed on ender 3, low quality .28, 50 percent infill. Takes about 2 hours to print. ... It holds saw blades.

A jigsaw blade holder holds up to 15 blades

simple blade holder for jigsaw blade. ...amount of used flament is not much

Jigsaw bade holder

Holder for jigsaw-blades, works with t-blade and will also fit blades with protective coating. ...Has place for 10 x 3 = 30 blades Source file can be found here:http://a360.co/1PRm3Ed How I Designed This Made in Autodesk Fushion 360

I needed a holder for jigsaw blades, printed the Ultimate Jig Saw Handle, however, the parts couldn't fit each other and the blade couldn't fit as well. One issue might be the orientation of the handle and the knob. The threaded portion of the handle...

... a wee paper shim and some hot glue to make sure they don't shoogle out. The outer most blade holders are made for larger blades like coarse woodcutting ones with splayed teeth. ... Check out my other designs for more Ryobi add-ons / randomness!

... use a wee paper shim and some hot glue to make sure they don't shoogle out. The outer most blade holders are made for larger blades like coarse woodcutting ones with splayed teeth. ... Check out my other designs for more Ryobi add-ons / randomness!

A blade holder for jigsaw blades. Inspired by https://www.thingiverse.com/thing:4680797. I built this with a two-part handle, secured by two M3x8mm cap screws with two nyloc M3 nuts. There are two types: - Blade holder 1 is for "U" shank blades -...

I needed a simple box for my jigsaw blades and i couldnt find any that i liked, so i desigend this one.Print the top 2 times and the bottom once. ...i used three perimeters, its almost printed solid. I also added a wider version for wider jigsaw...

Holder for 10 Blades. I named the versions with the length of the blade (the part with teeth). So there ist a version for short (55mm) blades, a medium sized one (75mm) and a 125mm version will follow. I am thinking about a version that is...

Jigsaw blade holder for slightly larger jigsaw blades remixed from a great original design. ... Thanks to the original creator!

This is a jigsaw blade holder that fits snugly in the top lid of your Sortimo (Bosch) toolbox. It holds 15 blades fixed in position by a locking slide bar, that can be unlocked by pressing any of the two ambidextrous release buttons. This is done...

Could not find a good holder for all the used (not to be thrown away yet) spare blades to my 18V Bosch jigsaw (GST 18 V-LI S), so I spent waay too much time developing this mount.This is a jigsaw blade holder that fits snugly in the top lid of your...

They are also compatible with the new Craftsman cases This is an insert that fits into one of these cases to hold T-shank jigsaw blades.You can fit up to 20 blades into one insert. I've included openSCAD and STL files. The SCAD file really isn't...

Replacement legs for my Vizio E50-E3. I do not have original part, so I made it using caliper and photos from internet. vizio_e50_left_leg.stl and vizio_e50_right_leg.stl - full size models vizio_e50_left_leg1.stl +vizio_e50_left_leg2.stl =...

Redesigned CC2224Max's holder as it didn't fit any of my T-shank blades. Blades differ in thickness (1.2mm to 1.7mm) so these slots are 2mm wide. Insert blades at an angle (10° to be precise) and then lower them to lock in the protrusion of the...

I created these T-shank jigsaw blade holders to work with my [Slim Packout Bins for Milwaukee bit holders](https://www.thingiverse.com/thing:3712826), but they also work in the original Milwaukee bit cases. I'm not sharing the openSCAD file yet.

einzeln - single Reihe 20 - row 20

I have a variety of jigsaw blades and wanted to store them in one place in the jigsaw case (fits the one from Parkside and Bosch). This design allows to stack a lot of different sizes slots into a single sliding box. To assemble you will need a...

Customized version of https://www.thingiverse.com/thing:3341387 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3341387

Jigsaw blade holder, T type. Mounted here in French cleats, but there are 2 fixing holes 4 mm. Support de lames de scie sauteuse, type T. ...Monté ici en "french cleats", mais il y a 2 trous de fixations 4 mm.

Legacy version with fewer & smaller windows are available, but I didn't upload them as the 2.0 is so much better. Original files at https://cad.onshape.com/documents/8371710b0e07c3e218f0947d/w/02ca39df6934bf7a40acb4d4/e/63a2d2bb2d613b8b9fd138c3...

This thing was made with Tinkercad. ...Edit it online https://www.tinkercad.com/things/fopxgCZAt6W

I got inspired by the jigsaw t-shaft hodler by @rafalmag https://www.thingiverse.com/thing:4582722 the blades were a little loose and the hole was too big for M3 inserted nuts. I started to modify the design to 4 blades with a tighter fit and a...

A box to hold the 3 stock blades that come with the Parkside battery jigsaw . There is room also for the hex wrench. ...It fits nicely in the space for the 2nd battery.

Pumpkin knife handle for using any T-shank jigsaw blade. ...There are two halves and a small key that sits in over the blade to keep it secured. One half uses heatset inserts: short #6 32tpi The other half uses 1/2" pan head #6 32tpi pan head screws 4...

Jigsaw blade holder for larger (145mm max) jigsaw blades remixed from [thing:4617787](https://www.thingiverse.com/thing:4617787). ... Openscad file for quick resizing included.

This is a remix from Jigsaw blade handle by Tadziurski (https://www.thingiverse.com/thing:2470470). I add two M2 bolts close to the blade to ensure tight securing for the blade. Alao, I modified the existing M3 bolt holds to receive "squared-headed"...

A small box for my jigsaw blades with a slideable lid. ... Its designed for blades with a thickness of 1,5mm.