jlf tp 8yt 3d models

Desk managment thing

Allows to hold the TPLINK switch under a table or on the wall. ...Can be secured using screws or zipties.

Enhanced Design Simplifies Wr841n Wall Holder Assembly: A revised version reduces material usage while strengthening critical components, such as pins that frequently fail due to excessive stress. ...To ensure structural integrity, print this design...

This bracket makes it possible to securely attach your Deco M9 Plus to a wall, ensuring a stable and convenient placement that maximizes your home's Wi-Fi coverage.

Humans reach a plateau at approximately 30% of their maximum aerobic capacity.

Climbing frame replacement washers feature a unique locking lug on their reverse side, preventing them from rotating freely. ...The rounded front edge of these washers ensures that they won't snag or catch on clothing items during the washing cycle.

I wanted a wall mount for my mesh router/AP so here it is. has keyhole slot for #8 screws set 1.5" apart on center. ...cheap plastic drywall anchors worked fine.

This simple toilet paper holder does its job effectively. Printing two of these units works perfectly well when there's no convenient wall to attach one side. The design accommodates a 125mm diameter roll, so scale it up if necessary. A strip of...

Custom designed Deco M4 support. The power cable and ethernet ports are clear of obstruction. Can be mounted with a single M4 - M5 bolt. The fixing bracket is reinforced to support the weight of the mesh. ... Tested in PLA with 25% and 3D...

I'm looking for a wall mount that fits my Nintendo Switch perfectly, so I'll just create one myself and save some money.

Remixed to suit the Deco M9 Version

The Compact Mounting Clip is specifically designed to hold the sleek and modern TL-SD1005D Desktop Switch securely in place on any flat surface, keeping it organized and out of sight. Its slim profile makes it easy to install and remove as needed,...

The mounting bracket for the left-hand side, which houses the power supply jack, is referred to as "Halter links." Meanwhile, "Halter rechts" denotes the right-hand side. Be cautious when dealing with the screws, as they have a tendency to break. The...

I printed it in PLA without supports and turned out great.

remixed to wall mount over electric face plate. ... Need longer 8/32 screw.

My wall mount broke and i needed a replacement, so i designed this. Its easy to print, just enable bridging and print. I recommend using more perimeters for a more stable result. ...Took me 23 minutes to print on my Prusa MK3S with 4 perimeters at...

This is a unique custom case, reworked by an amateur using Tinkercad's user-friendly interface. I'd like to give credit where credit is due - the original design can be found here: https://www.thingiverse.com/thing:25257. As for me, I simply...

300Mbit/s Wireless LAN Access Point EAP115 Wall Plate Installation

I modified the Mount design from Opossums' creation on Thingiverse (https://www.thingiverse.com/thing:1624523), adapting it to fit snugly behind my television. ...I utilized M6 screws and leveraged the 200x200mm Vesa mount that came with my TV for...

V2 24.12.2020 Screw holes are enlarged. The gullets have been corrected. Since it is mounted on the wall, the cable outlets are given to the side sections. Because the Deco it carries is expensive, it was built with 25% full for durability. ... ...

<p>I made this to mount my router by hanging it from an existing picture hook. I printed it upright with a brim and supports in PLA. ...If you're going to print this, make sure you have tuned your printer very well for dimensional accuracy, as there is...

a

Added third holder at the bottom, so you can hang it upside down if needed.Lid fits better, it's tighter, by higher and a bit wider walls.But still I used glue to connect it.I added as well 2 blocks to keep the distance from the wall and keep the...

Remix of a remix! The one from Dlernstrom is the right size, but the prongs are very thin. They kept snapping before I could even install the mount. I used their part as a template and made a new one from scratch in Inventor because I'm garbage...

I designed this wall mount for my TAPO c110 camera so I don't have to drill holes in the wall and instead,I used double sided mounting tape, and I use this camera in multiple areas, so I can easily remove and install it in other area.

This is a filament-, and time-saving remix of the Tapo C200 bracket.

This 3D model was initially designed using Sketchup 13, after which it was transformed into all other relevant 3D formats. The native format is .skp, while the 3dsmax scene is based on 3ds Max 2016 version and rendered with Vray 3.00 To view this 3D...

Print with 20% infill. Super glue parts 1 and 2 together as per the diagram to create the base. Screw the base to the wall, place the router onto it, and then measure and mark the required location of Part 3. Remove the router, screw Part 3 to the...

This 3D model was originally developed in Sketchup 8 and then exported to all other formats as a native .skp file format for maximum compatibility with multiple software programs. A compatible 3ds Max scene is available for seamless import into the...