jobsite table saw dust collection 3d models

Adapter for the Kobalt Table Saw to go from the standard port on the bottom to connect to 2" PVC fittings or 2.5" dust collection hose.

DWE7491RS Table Saw Bottom Hose Adapter to hook up a Bauer shop vac hose, might work with other models of Dewalt Table saw but havent tested. Might work with other models of shop vac hose. ... The hose connector portion has a diameter of 45.25mm.

Dewalt DWE7485 table saw dust collection dapter

I created this adapter for the Dewalt 7491 jobsite saw (table saw). It allows you to use a 2.5 inch vacuum hose on the bottom port of the saw for dust collection. ... The inside of the adapter is tapered for a friction fit.

I've been placing a bucket under my Rigid table saw to catch the majority of dust that falls through the dust chute. Dust bucket be gone!This is a reducer from 4" (table saw) to 1.75" (shop vac). Both my tools are Ridgid brand. Adapter is press...

https://www.thingiverse.com/thing:4613016 The updated version is designed around the 2.5" ultraflexible hose on Amazon and has an adapter to take advantage of the blade guard in order to collect dust from both under the blade and over the blade. ... ...

this is uploaded from the raven https://www.theraven.us/index.php/2020/02/22/dewalt-miter-saw-dust-collection/

This is a coupler for the 1.5 inch pipe used for the Overhead Dust Collection on a harvey table saw. This can be used to quickly connect the pipe after cutting. This will provide a friction fit. The pipe needs to be removed if you have a...

Dust Collector upgrade for Rigid Table Saw (model #TS3650) The original dust collector port attachment has only a 2.5" port for a standard Shop-Vac. This adaptation allows for a 4" dust collector hose without the need for a 2.5" -> 4" adapter. 1.1 -...

Dust Collector upgrade for Rigid Table Saw (model #TS3650) The original dust collector port attachment has only a 2.5" port for a standard Shop-Vac. This adaptation allows for a 4" dust collector hose without the need for a 2.5" -> 4" adapter. 1.1 -...

Thanks!https://paypal.me/cdsmakestuffDust Collector upgrade for Rigid Table Saw (model #TS3650)The original dust collector port attachment has only a 2.5" port for a standard Shop-Vac.This adaptation allows for a 4" dust collector hose without the...

Dust collection funnel for a 30year old Craftsman Table Saw. I was using a flat plate, but it clogged up with dust often. ...We will see if this is an improvement.

I stopped using my table saw a little while ago because it makes too much dust in my garage. I looked online to buy something like this but couldn't find exactly what I wanted. I made this simple design in Tinkercad. ...The hole at the top is for my...

... following video explains the whole thing clearly. Dust Collection Nozzle For Scroll Saw Loc-Line https://youtu.be/5f6m2yTiWcQ You may also be interested in the following: Excalibur Scroll Saw - Dust Collection Part 2 https://youtu.be/7t5EKRpA9m4

I tried to improve the dust collection of by 14" band saw. I got inspiration with this video: https://www.youtube.com/watch?v=QTLZtKWuvGs Design is not perfect... but it works. I use magnets to attach it to the plate but this can be improve. ... ...

I don't expect many of you to be able to use this as is, but I hope this will inspire you to improve dust collection on your band saw (which in my experience is generally not that well implemented). ... I have included the Fusion360 file so that you...

I designed and printed this adapter to capture dust from my Dewalt circular saw. I used a bolt to attach the adapter to the hole in the dust guard and wire to prevent it from swinging down and away from the dust port. ...I sized the circular hole to an...

I designed and printed this adapter to capture dust from my Dewalt circular saw. I used a bolt to attach the adapter to the hole in the dust guard and wire to prevent it from swinging down and away from the dust port. ...I sized the circular hole to an...

## About Simple miter bar to fit t-track channel of Hitachi C10RJ 10" 15-Amp Jobsite Table Saw. Used these to make a a cross cutting table saw sled made of birch plywood - 48 in x 18 in x 3/4 in. Printed 2 of these and put on each end of the sled. ...

Jobsite Table Saw, on which I broke the little springed sliding retaining fingers off the fence slide while removing the fence. I could probably have them replaced under the warranty or the lifetime service agreement, however I wanted my saw fixed...

I liked the edits on the featherboard done by r00nee, but the miter bars didn't fit in my Ridgid table saw miter slots, so I edited in order for them to fit. While I was at it, I changed the bottom of the bar to hold either 1/4-20 Hex nut or...

I liked the edits on the featherboard done by r00nee, but the miter bars didn't fit in my Ridgid table saw miter slots, so I edited in order for them to fit. While I was at it, I changed the bottom of the bar to hold either 1/4-20 Hex nut or 3/8-20...

It's connection part for DeWalt 7xx series job site table saw to stabdart 100cm or 4 inches dust collection pipes..

This a dust collector, guard, splitter for saws that were made before saws came with riving knives standard. The riving knife only works for square cuts as it is built in to the throat plate. I have been using a throat plate for years, and this is...

... on this one (https://www.thingiverse.com/thing:2767618) by https://www.thingiverse.com/wt808. ... It was modified for an 1 1/4" Vacuum connector and a wider shield 34mm vs. 30mm. This is specifically for Craftsman Table Saw Model 315.228310. ...

This is a Dust Collection Hood that surrounds the saw blade to collect the as much saw dust as possible. I have a small printer so I printed this in pieces and dovetail them together so no glue is necessary. This fits the Bosch GCM12SD Miter saw. ...Im...

I designed this because I was not happy with the OEM dust collection on my Milwaukee Miter Saw, my preference in the shop is to connect my vacuum to it so that I have less cleanup afterward, but the saw came with a rectangular port for some strange...

Adapter to my Tool Shop Miter Saw so I can connect it up to my dust collection. I'm using a Rigid Shop Vac host for the larger end of the adapter. ...Customized version of http://www.thingiverse.com/thing:1246651 ...

This re-uses the red composite ring from the original dust collection bag that comes with the saw. Simply remove the ring and place it onto the printed adapter. The dimensions are identical to the Bosch component where it is inserted into the saw,...

This is an adapter for a bigger dust collection hose. ...~60mm or 2.3" hose