jr z 3d models
79058 3d models found related to jr z.cults3d
Replacement bracket for the z axis nut holder in a Printrbot Jr. Reduces the amount of play the z axis nut had to a minimum. Replaces the original threaded rod and nut with stainless steel M8 threaded rod, two nuts and a spring in between the two...
thingiverse
Replacement bracket for the z axis nut holder in a Printrbot Jr. Reduces the amount of play the z axis nut had to a minimum. Replaces the original threaded rod and nut with stainless steel M8 threaded rod, two nuts and a spring in between the two...
thingiverse
This replaces the normal adapter that holds the bolt on the printrbot's z axis and change the sizing to fit an m6 nut. ...You will need to print 2 of this piece
thingiverse
I got some stainless steel threaded rod from Home Depot the other day, and some stainless steel nuts, and I wanted to upgrade my somewhat bent z-axis threaded rod. I had seen something similar for the Printrbot LC I think, so I made one to fit my...
thingiverse
a camera mount for my da vinci jr you will need a m3 screw to attach it and thats all Print Settings Printer: xyz Da Vinci Jr Rafts: No Supports: No Resolution: .2 Infill: 20%
thingiverse
Made 3 iterations of the Z endstop clip and the last one had the best fit/tighest tolerances... Only a 3 minute print, but HOURS of SAVED AGGRAVATION!!! AWESOME! ... This should have been standard on the PBjr,
thingiverse
Instructions This was inspired by the model made by Brian Evans for an M6 threaded rod, however this idea does not work with an M8 rod without doing some much larger alterations to the z/y carriage. The "missing sides" of the hexagonal tube are to...
thingiverse
These are accessories for upgrading to a 5mm Z-rod, The reduction of edge waviness, makes the conversion a must have, both items have been printed with a 5mm z-rod and the quality speaks for itself. Make sure to properly update the firmware based...
thingiverse
8 mm Bearing Blocks (bearing sleeves) Z Block 8mm spacer for 608Z bearing and for board placing Instructions Push inside of the block the bearings, the will fit very tight for stability purposes, hammer them gently until they go all the way in. The...
thingiverse
My wood couplers have not cracked yet but I assume they will eventually so it was time to print a set.
thingiverse
A holder for the bolts that holds the Z endstop screw in place on the Printrbot Jr. The screw kept loosening and the bottom bolt rolled down, so I made this little holder ting. Seems to work just fine (although it could - should - be tighter around...
thingiverse
Z-Achsen Stabilisator für deutlich bessere Druckergebnisse. Passt für den da Vinci Jr. 1.0 Pro 3D-Ducker in Verbindung mit 5 x 11 x 5 mm Kugellagern. Zusätzlich kann mit diesem Stabilisator auch der Winkel zwischen X-Achse und Y-Achse genau...
pinshape
Buscando una solución para el conocido problema que tiene la Printrbot Jr v2 en su eje Z, tanto en la alineación del husillo como en las guías, desarrollé este simple sistema que estabiliza estas guías. Solo debes imprimir cuatro veces este archivo y...
thingiverse
Buscando una solución para el conocido problema que tiene la Printrbot Jr v2 en su eje Z, tanto en la alineación del husillo como en las guías, desarrollé este simple sistema que estabiliza estas guías. Solo debes imprimir cuatro veces este archivo y...
thingiverse
Leave a space inside the coupler between the top of the motor shaft and the bottom of the Z-shaft. Use a 5mm wide rubber band and insert it into the spiral; this prevents vibration and stops the spiral from compressing. Use a shorter M3 screw...
thingiverse
... ...http://www.thingiverse.com/apps/customizer/run?thing_id=52734 Instructions Using the following options: message = JR stick_width = 8 font_size = 10 Font = write/orbitron.dxf hole_radius = 3 stick_thickness = 3 font_thickness = 5 flat_bottom = 1
thingiverse
... ...http://www.thingiverse.com/apps/customizer/run?thing_id=52734 Instructions Using the following options: message = JR. ...stick_width = 8 hole_radius = 3 flat_bottom = 1 Font = write/orbitron.dxf stick_thickness = 3 font_thickness = 5 font_size = 10
thingiverse
... with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=40704 Instructions Using the following options: ring_size = 18.14 Font = write/Letters.dxf message = JR ring_width = 6 font_spacing = 0 ring_thickness = 1.6 font_size = 10
thingiverse
... Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=753477 Instructions Using the following options: size = 20 spacing = 1 extrude = 5 direction = ltr web = 0 font = Trocchi text = Jr
thingiverse
Customized version of https://www.thingiverse.com/thing:2850939 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=2850939
thingiverse
Customized version of https://www.thingiverse.com/thing:2482372 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=2482372
thingiverse
Customized version of https://www.thingiverse.com/thing:4681765 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=4681765
thingiverse
Customized version of https://www.thingiverse.com/thing:714444 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=714444
thingiverse
Customized version of http://www.thingiverse.com/thing:52922 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=52922 Instructions Using the following options:...
thingiverse
Customized version of https://www.thingiverse.com/thing:2850939 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=2850939