jsn sr04t 3d models

JSN-SR04T Ultrasonic Sensor Module Board.

JSN-SR04T Sensor Mount v11

Sensor holder for JSN-SR04T

A simple wall-/ceilingmount with elongated holes for the JSN-SR04T.

This is a model of the JSN SR04T 3.0 Ultasonic outdoor distance model. ...The one used in autos.

Enclosure for the JSN-SR04T-2.0 electronics. the sensor box is optional. the sensor connector on the back of the board was removed and re-soldered at a 90 degree angle. hot glue was used to secure the connector. to secure the board on the lid i...

JSN-SR04T Waterproof Ultrasonic Distance Measuring Module case with lid. Feel free to remix if needed, the lid is very tight the first time you try to put it on. I need to find a way to get it to not move around so much inside even thoguht it's...

JSN-SR04T Waterproof Ultrasonic Distance Measuring Module case with lid. Feel free to remix if needed, the lid is very tight the first time you try to put it on. I need to find a way to get it to not move around so much inside even thoguht it's...

JSN-SR04T-2.0 Ultrasonic Sensor

A simple case/hold for JSN-SR04T-2.0 UH sensor. Made in 2 pieces, so don't need supports. Just glued together. Top part can also be printed attached if wanted, but I needed it to be separate at first (To fit better). Support needed for the...

I used  JSN-SR04T waterproof ultrasonic sensor to calculate the water level in a water tank. The idea is to calculate the distance to the water level and use that number to calculate the volume of water inside the tank. The sensor is...

<p>5° tiltet holder to correct the tilt of the sensor</p>

Waterproof ultrasonic sensor module.

This is a holder to attach your outdoor ultrasonic sensor JSN-SR04T to a SolarEdge / KEBA EV charger. I use this to detect whether my car stands in front of the garage and if so, to block opening / closing the garage door. This prevents damages to my...

This is a cone to narrow down the opening angle of the ultrasonic distance sensors of the watertight SR04 types. It also puts a bit of distance between the sensor and the surface, to compensate for its inferior minimum measuring distance. This...

I've tried the original design without success. I've remix it to look like this: https://www.maxbotix.com/ultrasonic_sensors/mb7588.htm It improved the signal a lot. ... There is another design but i didn't try it because its to big for the space I...

Customized version of http://www.thingiverse.com/thing:52734 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=52734 Instructions Using the following options: ...

Customized version of http://www.thingiverse.com/thing:248635 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=248635 Instructions Using the following options:...

JSN-SRO4T

JSN Chair

Housing for waterproof ultrasonic sensor SR04T. Consist of both electronics board housing and sensor housing. ...Intention is to use this sensor for water level measurement in a barell.

Housing for waterproof ultrasonic sensor SR04T. Consist of both electronics board housing and sensor housing. Intention is to use this sensor for water level measurement in a barell. ...

This is a ultrasonic sensor that comes with the JSN-SR04 sensor electronics.

Case for the ultrasonic sensor SR04T. Strain relief and holder for circuit board included. No screws needed. I was to lazy to implement a clip mechanism for closing the case. ... Just use a cable tie or electrical tape to hold the cover in place.

High resolution Tiles Chair by JSN Design. The wood material assigned to the panels of the chair uses 1 2048x2048 diffuse texture; the material assigned to the cushion uses a 3D Studio Max internal procedural noise map as displacement texture. The...

Módulo Sensor Ultrassônico Impermeável Jsn-sr04taj-sr04m

3ds Max model of the JSN rhombus chair. Unit measures: 821mm wide x 824mm deep x 1035mm high. The model was created in 3ds Max 2020. Render - V-Ray 4.10.03. I will be glad to answer your questions . ...Good luck ;-)

Modern JSN Chair is a high quality, photo real model that will enhance detail and realism to any of your rendering projects. The model has a fully textured, detailed design that allows for close-up renders, and was originally modeled in 3ds Max 2016...

In the middle there is a hole for the JSN-SR4T Sensor (ultrasonic) I placed all the electronics in water proof upper part. As the sensor needs minimum 20-25cm distance, the entire system is placed 20cm above waterlevel. To avoid reflections...

# Threaded cone for ultrasonic distance sensors. ... - Thread diameter: 28 - Thread pitch: 2mm - Heigth: 66mm - Outer diameter: 44mm - Inner diameter: 21.8mm