jst ph crimp tool 3d models
105647 3d models found related to jst ph crimp tool.thingiverse
(The SN-2549 is for JST and DuPont connectors and crimps both parts of the contact at once.) Link to the tool: https://iwiss.com/products/icrimp-sn-2549/ The gridfinity storage box pictured:...
thingiverse
This part is to mount my JST crimper tool to an IKEA Skadis. ... I used PETG but PLA should be fine.
thingiverse
Remix to add a small lip to keep the tool more secure.
prusaprinters
Remix to add a small lip to keep the tool more secure. Print Settings Printer Brand: Creality Printer: Ender 3 ProRafts: No Supports: Yes Category: Tool Holders & Boxes
thingiverse
These are JST-PH 2.0 caps so you could easily see which of your batteries are charge.
grabcad
JST PH connectorsThese pitch is 2mmReference:http://www.jst-mfg.com/product/pdf/eng/ePH.pdf
thingiverse
This is a battery cap for a 1S Lipo with a JST-PH connector. I used these when replacing the connectors. ...
thingiverse
Simple holder for an Ethernet crimping tool. ...Can be screwed to a wall with Ø4mm screws.
thingiverse
A quick remix of alecreator's Ikea Skadis holder for crimping tools, adapted to a standard pegboard using twobraids' blank
thingiverse
JST-PH 2.0mm pitch 2 pin PCB-side male connector. Pins are 0.5mm x 0.5mm, ones from 2mm pitch pin header fit perfectly. Don't use ones from 2.54 pin header, they are way too thick for the mating connector. May be printed with 0.4mm nozzle/0.2 layer...
thingiverse
These JST-PH connectors are really tiny! I just don't have enough hands to get this to sit in the crimper plus hold a wire and and hold the crimper itself. Nor can I justify spending $800+ on a crimper that come with a locator. Time to make one...
prusaprinters
A quick remix of alecreator's Ikea Skadis holder for crimping tools, adapted to a standard pegboard using twobraids' blank Category: DIY
thingiverse
crimp tool jaws box for a 9 jaws version: https://www.aliexpress.com/item/32811893136.html neodymium magnets 4x 18x8x5mm (from spare parts) added hex key slot, and pocket for a jaws sheet legend
thingiverse
This is a replacement for the really bad clothes-clip like magnetic thing that Molex provides with their "0640160205 Hand Crimper Tool Rectangular Contacts, 18-30 AWG Side Entry, Ratchet" to hold the crimp connector while crimping. The crimper is...
prusaprinters
Simple holder for an Ethernet crimping tool. ...Can be screwed to a wall with Ø4mm screws. Print Settings Printer Brand: Prusa Printer: i3 MK2.5 Supports: No Category: Tool Holders & Boxes
thingiverse
I lost the jaw for my IDC ribbon cable crimp tool. This jaw is for the standard 0.100-inch pitch (0.050 inch conductor pitch) IDC plug. I added tabs that should help keep the jaw attached to the tool. The provided STEP model includes a...
thingiverse
I'm not sure what happened with my RJ45 crimping tool, but the plastic socket that holds the connector while criping broke off and fell into small pieces. As I have not found any replacements for it on this wonderful site, I decided to design one and...
grabcad
For other Pin configurations or other formats just ask in the comments.Dimensions according to http://www.jst-mfg.com/product/pdf/eng/ePH.pdfLink to onshape Document:...
thingiverse
... from 3 & 6 mm sheet stock the pieces should go together quite logically. Then grab a cheap pair of of the shelf hand crimps (we used these pair http://oom.lt/yXUoiR ) cut the bits out and bolt together. ...You'll be effortlessly crimping in no time.
thingiverse
Note: You will need JST-XH (2.5mm) crimp pins, some wire (I used 28 AWG stranded) and a crimper. My FreeCAD design file is included. I used PLA Pro at 215C/55C, 0.2mm layer height, (or 0.1mm) 1.2mm walls, 0.8mm top/bottom, 40% infill with a...
prusaprinters
This is a connector housing for a standard Rotary Encoder with built-in pushbutton switch.You can find these at about any electronics supply house.Note: You will need JST-XH (2.5mm) crimp pins, some wire (I used 28 AWG stranded)and a crimper.My...
thingiverse
It is a simple device that clamps in the slot between the male and female connectors on a JST-HX connector. For most connectors you just slide the tool into place and give a gentle tug. If the plug is really on tight you can use a rocking motion to...
grabcad
JST PH Connector Pack (Through-hole, SMT) All sizes and types + Source files.PH Connector:2.0 mm pitch / Disconnectable Crimp style connectors 8.0 mm in height after mountingand 4.5 mm in width.• Current rating: 2 A AC/DC (AWG #24)• Voltage rating:...
thingiverse
The crimping tool I have was designed for RG-58 coax. But I needed to crimp some RG-8. I didn't expect it to last for very many crimps, just a few and it did and using PLA. Edit: 100% fill, Layer height 0.28mm, Wall Count 4. Add picture of...