jst sm 3d models
4850 3d models found related to jst sm.thingiverse
Testing a JST-SM connector cutout This model was made in Morphi! http://www.morphiapp.com. In Morphi, people of all skill levels can make 3D printable models on the go using touch, without wifi or a mouse. Download the app for free in the App store.
thingiverse
I have modified this end cap to fit a 4 pin JST-SM connector, since this is what I had on hand. I will be completing my MPCNC build soon so I will post pictures then. Note: I have not yet tested this but it shouldn't have any problems. I have tested...
thingiverse
Its a little panel for some JST-SM (4pin) connectors and XT60 connectors that I made for my OX Router. As I fit the controller and everything inside an existing computer [case], I needed a way to get the wires to the control board. So I made this...
grabcad
Female version here : 3-Pin JST Female ConnectorMale/Female 4-Pin version here : JST SM 2.54 4-PIN Male/Female connector
thingiverse
# JST-SM connector slots 2/3/4/10 pins Slots for JST-SM connectors. The slots are tight and the connectors won't slip out. ... I added some clips to secure them which are usually not necesarry ## Tinkercad source ...
thingiverse
This is a bracket the attaches a female 4pin JST SM connector to one of the towers on the Vertex Delta printer. ...I use this connector for my heated bed upgrade.
thingiverse
......The bracket can be attached by a clamp or by two M3x50 bolts, which replace two M3x42 bolts of the motor. The bracket has the following features: < the motor gets JST SM sockets < the motor can be cooled with a 40x40x10mm fan and a 25x25x10 heatsink
cults3d
......The bracket can be attached by a clamp or by two M3x50 bolts, which replace two M3x42 bolts of the motor. The bracket has the following features: < the motor gets JST SM sockets < the motor can be cooled with a 40x40x10mm fan and a 25x25x10 heatsink
grabcad
2.5mm pitch http://www.jst-mfg.com/product/pdf/eng/eSM.pdf Common plug found on chinese LED drivers
thingiverse
I wanted a case that had a JST connector with space for cable sleeving. I'm using 1/2 in sleeving and heatshrink. Case is a press fit, it should be very snug. If needed, add a drop of super glue in on corner to hold it in place. ...I also recommend that...
thingiverse
Needed just half of the original for retooling the control box of a MYDIYCNC.
thingiverse
... for a fused power connector and switch. ...Two spaces for XT60 connectors, 6 spaces for JST SM 2pin connectors or wires. POWERoPENBILD is a bit updated so it is not such a tight fit. ...The new STL works grate if you need any changes let me know.
thingiverse
... There are two variations: 1. JST XH 2.54 - requires soldering work on both ends. You can gently bend the pins of JST in right direction 2. JST PH-R 2.0 Any feedback appreciated. ### UPDATE 24.11.2021 Upon request I added JST XH 2.54 SM version
thingiverse
... - JST XH 2.54 - requires soldering work on both ends. You can gently bend the pins of JST in right direction - JST PH-R 2.0 - (new) JST XH 2.54 SM ### UPDATE 24.11.2021 Upon request I added JST XH 2.54 SM version - Any feedback appreciated.
thingiverse
After getting new 5015 blower fans to my Super Racer), the new fans have different connectors than the old ones. This is a simple adaptor so I won't have to hack up the new fan cables. Thanks Jetel73 for modelling the XH parts (used in this...
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=114247 Instructions Using the following options: ring_spacing = 2.5 ring_width = 5 ring_height_step = .5 pin_radius = 2.45 pin_hole_radius = 3 element = Sm center_radius = 12 font =...
thingiverse
Fed up with silly harnesses and power distribution board? ...Make a JST power board! I'll also make a 5v backplate. I'm using 22AWG solid core wire for the harness and standard JST pins.
thingiverse
This is a JST secured Socket for secured connection of 2S Lipos with JST Plug to receiver for example. This is designed to prevent powerloss and to prevent polarity reverse. ...