k8200 controller board 3d models
159333 3d models found related to k8200 controller board.thingiverse
This is a case for the K8200 Controller Board. ...Links to buy the parts I used are in the instructions Instructions Banana Terminals: ...
thingiverse
... on the frame, FULL (http://www.thingiverse.com/thing:221362) or FLAT (http://www.thingiverse.com/thing:225642) clip may be used. You can find more details on my blog: http://ljwinkler.blogspot.com/2014/01/controller-board-mount-for-velleman.html
thingiverse
Knob for the encoder of the VM8201 friction fit onto the spline
thingiverse
Cover for K8200 Printer-Board with or without fan (50mm) grill. ...I added Covers with 40 60 and 80mm Fans without Grill
thingiverse
Simple sexy control board mount and cover Let your imagination flow! ... Instructions Find a fan mark the holes and mount it onto the cover I would cut away if you mount a fan Removing the grill will cut...
thingiverse
It can be used with the existing screws that are used to attach the controller board, all that are needed are 4 screws to attach the fan. The only thing I'd add next time is more square holes on the right hand side to slide cables through, otherwise...
grabcad
A support boards with housing and a Raspberry logo for your 3D printer
thingiverse
simple support for fan controller board Must have 2 bolts M5 , 2 nuts M5, 2 bolts M3 support for fan 50x50 supporto for fan 60x60
thingiverse
A cover including a fan (40x40x20) and an extender allowing to command the reset button with the box closed. ... The grid is printed with the following specs : Layer height : 0.20 Solid layers : Top 0 - Bottom 0 Fill density 0.10 Fill pattern :...
thingiverse
Controller Box with upstands for the K8200 Board plus additional upstands for a 24V Heat Bed Conversion board. This was mounted to the frame using http://www.thingiverse.com/thing:1902822 brackets and http://www.thingiverse.com/thing:1873746 T Nuts...
thingiverse
I designed this box two Years ago for the controller of my K8200 3D-Printer. It can be mounted to the aluminum frame with M5 screws and its cover includes a cooling fan as well as space for a cheap step-down converter. This is used for fan speed...
thingiverse
This is a remake of the k8200 control board case found here: http://www.thingiverse.com/thing:168769/#files It has mounts for two 40mm fans and increased wiring room at the top and base of the case and uses the original designs base plate for...
thingiverse
This case is disigned for de K8200 and 3DRAG standalone controller from open-electronics.org http://www.open-electronics.org/autonomous-printing-with-your-reprap/
thingiverse
Useful if you're using Octopi, I've ordered a Pi0W and then it's just one USB over to the K8200 controller board. Update: I've got my hands on a Pi0W and using the stable octopi 0.13 image. It doesn't setup the onboard wifi out of the box. (the...
thingiverse
... ...Single strands, each with matching cable cross-section seemed more modification friendly to me. However, some cables are now much too long - and must be stowed somewhere. That's why I designed this controller base with a flanged cable shed.
cults3d
... K8200. ...Single strands, each with matching cable cross-section seemed more modification friendly to me. However, some cables are now much too long - and must be stowed somewhere. That's why I designed this controller base with a flanged cable shed.
prusaprinters
An K8200/3Drag enclosure for the RepRap Full Graphic Smart Controller.It was my design goal to achieve a solution with as few components as possible and preferably without screws. In the design process, my goals were achieved, but the solution was...
thingiverse
The original control board cover for the Velleman K8200 is not very well ventilated. I wanted to improved air flow and remade the front to sport a lot of hex formed holes. I also wanted the possibility to mount equipment under the cover so I added...
myminifactory
The original control board cover for the Velleman K8200 is not very well ventilated. I wanted to improved air flow and remade the front to sport a lot of hex formed holes.I also wanted the possibility to mount equipment under the cover so I added two...
thingiverse
An K8200/3Drag enclosure for the RepRap Full Graphic Smart Controller. It was my design goal to achieve a solution with as few components as possible and preferably without screws. In the design process, my goals were achieved, but the solution was...
thingiverse
This is the bottom cover for the original circuit board cover for Velleman K8200. The original cover only protect the top and side of the circuit board. The bottom of the board is still exposed. So using this bottom cover the circuit board can be...
thingiverse
While building the second Z-support http://www.thingiverse.com/thing:311980 I had to mount the Controller with a bit more space. So I have created a mount for the Controller which is more stable by using metric screws. You need 2 M5 screws with...
grabcad
This is a DC motor control board, which can control two DC motors at the same time.
grabcad
This is the servo controller board model which is used in MECE-8990.
thingiverse
Simple 'slide-over' cover for the Ooznest WorkBee CNC routers controller board.
grabcad
This is the KK2.1.5 LCD flight control board mostly used for FPV racing drones.