karcher vacuum hose connector 3d models

Replacement end connector for Karcher WD2 hose. As you can see from the pic mine was damaged and badly cracked so I made this replacement part to fit. Nice tight fit over the hose and other 3d printed nozzles for this vac fit perfectly over the...

This is a clip for Karcher vacuum hose (Model : WD 6) to attach the electrical cable of the tool you're using to the vacuum hose. There is two small tabs to avoid slipping on the hose. I printed them in PLA with 10% infill and the rigidity of the...

... Cyclone Dust Filter https://www.thingiverse.com/thing:2829268. ...But of course it can be easily modified to attach to other items too! Be sure to also check out the tool-side I made: https://www.prusaprinters.org/prints/34890-karcher-vacuum-tool

Simple Adapter for Karcher vacuum hose

... In these series; Metabo Miter Saw to vacuum hose https://www.thingiverse.com/thing:3371319 Vacuum hose to Karcher Shopvac (with wall clamps) https://www.thingiverse.com/thing:3371350 Vacuum hose wall clamps https://www.thingiverse.com/thing:3371362

Vacuum cleaner hose adapter for Karcher (model A 2003, but compatible with other models). Hose rotation enabled! FreeCAD model was supposed to be quite parametric driven by a spreadsheet, but some issues using FreeCAD made it difficult. Any advice...

Tested with my WD3 Premium, but it may work with any Karcher hose with the same style of tip. Several versions with angles (45° and 90°), inline (short/long), and the parametric Fusion 360 file to modify it as you wish. Careful, the short version...

4IN VACUUM HOSE CONNECTOR

Inside/outside connector for Vacuum cleaner hose

Vacuum Hose Connector ( to suit 51mm OD pipe )

Connecteur pour deux tuyau karcher série WD ou pour réparation.

This is to replace the Vacuum end connector on an older Fein vacuum hose. I was able to start with CLine's design 1550675 and create the remainder of the part which locks into the vacuum by measuring off of my broken part. You may need to adjust the...

Designed this for a quick release magnetic vacuum hose connector. Fits a 62mm hose. Uses 12.7mm (1/2") rare earth magnets; just press in place (mine were very snug) and use CA glue to make sure they stay put. May be adding some additional...

This thing was made with Tinkercad. ...Edit it online https://www.tinkercad.com/things/j1Al1xHAOxg Place piece e.g. foam under lever to keep vacuum hose locked

My vacuum cleaner hose broke down and I wasn't able to use it anymore. The part I printed fits both sides very well, I glued it to the part you hold in your hand so it won't come loose. ...It works great, try it out ;)

Connecting a hose to my sawdust collector. ...Didn't want to cut the supplied hose short.

Based upon the following design: http://www.thingiverse.com/thing:1001497 I needed a flate plate to connect a vacuum tube. ...The above design has been modified, and includes a centre hole locator for cutting the large hole thru which extract passes -...

Adapter from the hose found on the vacuum cleaner WD 6 P Premium from Kärcher, to a ~40mm hose.

Dyson DC29 vacuum hose connector. Simple design. Printable without support. ... openSCAD file included (BOSL2 lib is needed).

https://www.printables.com/model/283250-50mm-magnetic-vacuum-hose-connector 50mm magnetic connector for all common hose sizes (that I could find online). All adapters have: *Magnetic connector* - 50mm internal diameter - Positions for 8 magnets,...

https://www.printables.com/model/283255-100mm-magnetic-vacuum-hose-connector 100mm magnetic connector for all common hose sizes (that I could find online). All adapters have: **Magnetic connector** - 100mm internal diameter - Positions for 12...

... working again today, I sketched the connector by myself. After cutting off the damaged part of the hose, I glued it into the printed connector and assembled it. Need a replacement part on sunday afternoon? Ask your 3D printer for help! ...:-)

100mm magnetic connector for all common hose sizes (that I could find online).All adapters have:Magnetic connector100mm internal diameterPositions for 12 magnets, 10x3mm in size (magnet recess is 10.5x4mm).3mm clearance around the magnets.7.5mm...

Customized version of http://www.thingiverse.com/thing:97238 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=97238 Instructions Using the following options:...

These prints work as fully functional adapters for theMakita VC-3 and similar. Fit is perfect for my printer even the snap-fit but as usual, your results may vary. Fusion360 file is included for easy modification. It's meant to interface with <a...

Customized version of http://www.thingiverse.com/thing:97238 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=97238 Instructions Using the following options:...

It's always sunday when things get broken. today the hose of our bosch relaxx'x vacuum got a crack. I disassembled it and saw, that the hose was glued into the connector. The try to get the glue and the rest of the hose out of the connector failed....

As far as my research goes, there is about three different types of hoses: Two of them basically have the same connector on both ends (although it might look a bit different), the third one has a different connector on the vacuum cleaner side...

I was needing a part to connect a vacuum hose to my circular saw to extract wood chips and dustI designed the part in Fusion 360 with a female connector to enter the circular saw exits and an internal screw thread for the vacuum hoseI did several...

I was needing a part to connect a vacuum hose to my Mirka DEROS orbital sander to extract dustI designed the part in Fusion 360 with a female connector with internal screw to enter the sander exits and just a simple cone to connect the vacuum hoseI...