karearea talon 3d models
2034 3d models found related to karearea talon.
thingiverse
electronics protection for the original karearea talon. ...(does not fit the PR edition) still allows canopy to be opened, designed to fit with 4 in 1 esc, but tight fit.
thingiverse
Designed this to help protect the antenna on the Karearea Talon Quadcopter as I feel this is the one fragile point in a fantastic frame. This also gives some protection to the receiver antenna as well. This way it should hit the antenna where it...
thingiverse
Just a simple antenna provision I created for the Karearea Talon SVX. ...Needs to be printed with a .2 nozzle with .1 resolution, otherwise Cura will chop up the tubes, Slic3r will do it with .4 nozzle and .2 res, but the results aren't great.
thingiverse
This is a simple GoPro Session Mount for the Karearea Talon. Mounts to the front standoff above the camera and the tab on the back slides under the horizontal CF plate on the top. Approximately a +30 degree angle on top of the 5-10 degrees that the...
thingiverse
WARNING: The Karearea Talon is not designed to be used without it's carbon fiber pod. By running this pod you increase the chances of damaging the aluminium parts of the frame in a crash. Use at your own risk. ... A lot of time and effort went in to...
thingiverse
Pod for Karearea Talon V2 designed for 3-4 layer 20x20 stack and 14x14 camera with M8 lens at 45 degrees uptilt. designed with strong semi rigid print material in mind like Polycarbonate (pictured) or nylon. ... may need to be made thicker for TPU.
thingiverse
Mount for an AXI Ufl on the Karearea Talon using a TBS Crossfire Micro standard Antenna
thingiverse
Universal GoPro mount for the Karearea Talon FPV racing quad. I used the original base GoPro moutnd designed by the Karearea team and modified it with the standard GoPro mount. Designed to be printed, with supports, in a rigid material with good...
thingiverse
Hello there, I am sharing my Realacc Real1 (Karearea Talon Clone) customized Top. Please don't be mad, I mixed some files which are available here, but I don't know which one anymore. Feel free to contact me so I can mark them as remixed (or...
thingiverse
pod/canopy for Karearea Talon PR, brings the camera back to the front of stack and has a fin for both turtle mode and also affects cornering. Please keep in mind this pod has been tested primarily on a track set up in a well maintained sports field,...
thingiverse
This POD has been designed for the KAREAREA PR 5" racing drone. It has been highly customised for a Runcam Swift or Swift 2 micro camera or a Foxeer Predator micro camera. It may suit other micro cameras which I have not tested. The RC antenna wires...
thingiverse
Cutsom 3dprint mounts for Lumenier AX2 stubby vtx antenna, Immortal T antenne, lipo cable mount+led mount
thingiverse
Karearea Talon PR V2 5" Racing Frame , Arm Guards
thingiverse
New version of my Talon motor bumper that now has a built in softmount. ...This means you don't have to rely on the motor screws holding it in place. I print it off in 2 parts, (the sock separately) and the melt it together once mounted on the Talon :)
thingiverse
The arm tubes will destroy all the awesome flight characteristics of the Karearea Talon, but will also make the Talon far more predictable in the wind. Pod is designed around a micro swift and a ufl AXII VTX antenna. ...Also has 2 RX antenna holes,...
thingiverse
GoPro mount with a spot for the buzzer for the Karearea Talon FPV racing quad. If you mount the FPV camera on the lower mount, the buzzer (standard piezo buzzer with 11.9mm diameter) will use an existing hole in the carbon for the sound to escape the...
thingiverse
This is an antenna mount is for the Pictail of the TBS Unify (pro). I printed it in TPU so its a little bit elastic if you crash. Its not perfect yet maybe i will release a better version soon. You zip tie it to the topplate. ... It is...
thingiverse
This thing was made with Tinkercad. ...Edit it online https://www.tinkercad.com/things/8XNHqELqZzR
thingiverse
This thing was made with Tinkercad. ...Edit it online https://www.tinkercad.com/things/a45K3wUfUh4
thingiverse
Print in TPU and they should just slide on, no glue required :)
thingiverse
I made this because my topplate broke. It broke because the vtx-antenna mount is bulls***t The topplate is 4mm instead of 2mm because its plastic and not carbon fibre. I dont know if the new vtx antenna mount is stiff enough for a crash. If it...
thingiverse
Check out https://www.thingiverse.com/thing:2583813 , much better :) Added extra protection for the front motors.
thingiverse
Remixed Robs racing pod to allow fitment of an SMA connector for my AXII stubby antenna. I used 50% infill and HobbyKing TPU, its nice and sturdy. Kudos to bugg5532 for the initial pod design! My Flashprint software was putting in an unnecessary...
thingiverse
print with the lens as the base in TPU. ...You don't see any of the material on the camera lens :)
thingiverse
You will need two M3 screws to mount the holder. ...To fix the antenna straws, you can use electrical tape or a simple silicon tube, like on the picture
thingiverse
This is a fixed 30-35 degree GoPro mount for Karearea Talon SVX. It's a merge of the original Talon separate base and top adjustable mount. ... Best printed in flexible (NinjaFlex , TPU)
thingiverse
An adjustable action camera mount for the karearea talon V1. Being 38mm wide means that you can fit both the GoPro session and the Runcam HD. To assemble you need 8 x M3x8mm screws and 4 M3 nuts. ...It is also recommended you use a non-slip pad to...
thingiverse
This is a canopy for Karearea frame Talon V2. Camera angle is fixed to 45° There's place for the buzzer. ...