keurig b 60 3d models
142029 3d models found related to keurig b 60.thingiverse
There are a few of these on Thingiverse but none fit quite as well as I wanted so I redrew it based on measurements of my machine, a Keurig B145. I have included a Solidworks 2018 model. Sorry, I cannot go back further than that. I have drawn this...
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=1264391 Instructions Using the following options: FPanel = 0 Filet = 2.1 BShell = 0 PCBFeet = 0 FootDia = 8 BPanel = 1 Length = 100 Height = 60 FootHole = 3 m = 0.9 PCBLength = 70 TxtSize = 3...
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=1355018 Instructions Using the following options: Police = Arial Black Width = 60 PCBLength = 70 PCBPosY = 6 PCBPosX = 7 BShell = 0 PCBWidth = 50 TShell = 0 FPanel = 0 PCBFeet = 0 Vent_width =...
thingiverse
This is a remix of the SLS Orion Model Rocket by grossrc. ...This version has a more enhanced abort tower and is designed for Estes B-60 Tubes (42mm). ...IMPORTANT: Cut the tube to 9 inches for the best look.
thingiverse
inspired by the keurig freedom key. you can cut out the rim of original Keruig cup and glue/tape it to by pass the DRM check. you can tape a purple post it note on other side to unlock the hidden menu (Vue Cup menu) if you want to make bigger...
thingiverse
... Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=121782 Instructions Using the following options: offY = 0 offX = 0 margin = 10 stencil_width = 80 stencil_thickness = 1 input = Jason`s Keurig
thingiverse
I'm lazy, so I installed a filtered water faucet above my Keurig, and melted a hole in the lid to fill it. I wanted it to be nice and finished, though, so I made this grommet to give it a nice finished look. Print solid. The hole in the lid was...
thingiverse
My Keurig 2.0 coffee maker broke the other day. I lifted the handle to load it and heard a snap. When I tried to close the handle it was jammed it would not close. I figured out if you pull down a part inside it then would close. After a day of...
cgtrader
Papilio Shell Designer: Naoto Fukasawa Typology: Chairs Collection: B&B Italia OverviewNatural materials take a cue from modern geometry. Gunmetal-finished iron forms uniquely curved angles to balance a contrasting brown tabletop of rich reclaimed...
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=16627 Instructions Using the following options: pulley_b_ht = retainer_ht = pulley_b_dia = 0 idler_ht = idler = 0 additional_tooth_depth = 0 additional_tooth_width = 0.2 motor_shaft = 8 profile...
thingiverse
Customized version of http://www.thingiverse.com/thing:1899670 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=1899670 Instructions Using the following options: scale = 8 font1 = Liberation Sans content = 60
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=16610 Instructions Using the following options: size = 60 screwinset = 4 cornerradius = 4 borderthickness = 5 spinerotation = 0 spines = 10 thickness = 2 spinesize = 2 screwradius = 2.3...
thingiverse
Coffee/Espresso Tamper/Compactor for Keurig or similar machine.
thingiverse
Quick Keurig Case for counter top. Holds 24 K-cups. ... Uses (2) 3 x 4 Keurig Trays.
thingiverse
This holds the Keurig reusable coffee cup-filter or the main disposable coffee cup packet cup.
thingiverse
This a splash guard, to prevent coffee from splashing as the Keurig brews it.
thingiverse
... couldn't open all the way. This allows for the full opening and closing of the Keurig coffee pod chamber using a short action (2.5"). This is designed to work with the Keurig hardware (Torx screw and washer); no additional hardware is required.
thingiverse
drip tray for keurig machine. ...just wanted my own stencil and I'm on a godzilla kick.
thingiverse
This is a smaller drip tray for my Keurig single cup coffee maker. ... My coffee mug is too tall with the standard tray.
thingiverse
Platform to get your coffee mug closer to the discharge when not using the carafe. ... It keeps the coffee splatters around the Keurig to a minimum.
thingiverse
Another version of my keurig drip tray with Godzilla. Hope you like it. ...My second attempt at making my own thing!
thingiverse
Fits Cuisinart DBM-8 Burr Mill Coffee grinder. ... Allows easy filling of reusable Keurig Pods. ... Locks cover onto bin while filling the Pods.
thingiverse
... K425 coffee maker. ...My tall mugs would not fit under the Keurig so this stand was designed to lift it up about an inch. to accommodate my laziness. ...Included are a whole stand, as well as split left and right pieces if you have a smaller bed.