keystone cat5 3d models
1778 3d models found related to keystone cat5.thingiverse
This is a simple bracket meant to mount a couple of keystone modules (cat5/cat6 ethernet jack connectors, etc.) to the wall. They should print standing up, with support inside the squares. ... Take note that the compliant springy hook on the keystone...
thingiverse
This is a replacement keystone for the board game 'Atmosfear'. ...We are missing several keystones from our copy of the game, but thanks to 3d printing we once again have a full set
myminifactory
This smaller keystone, which is used to hold architectural arches together, has only been identified as such in 2009, despite having been in the Lapidarium for many years. It probably comes from the side chapel of Church of the Holy Cross, now...
thingiverse
Cat5 Cable clip. ...Use drywall anchor to mount to wall or directly to wood.
grabcad
Cat5 mount with 2.5 holes for self-tapping screws.The jpeg file is demonstrative to indicate the type of Cat5 fruit intended.I recommend printing it by placing it from the back.
thingiverse
This is a wall clip for routing CAT5 network cables mounted with a thumb tack/push pin.
thingiverse
I was needing a plug to cover the LAN input to a project I was doing (Heatermeter) so I designed this. ... Should fit most cat5 or cat6 jacks.
thingiverse
version is easier, stronger and 3 pieces (Cat5 UTP; Cat5 STP; Cat6). And FreeCAD design. And now, PLA is good for this. ---------------------------------------------------------------------------------------------------- This is my first...
thingiverse
This is a simple mount for a single RJ45 CAT5/6 cable breakout board. Once you remove the cable chain, this can be directly mounted onto the hot end carriage. ... Say goodbye to those ugly wires!
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=47956 Instructions Using the following options: 1st_plate_bottom_hole = cat5e 5th_plate = none 4th_plate = none plate_size = 0 4th_plate_bottom_hole = none 2nd_plate_bottom_hole = none 3rd_plate...
thingiverse
Print this out, slip the male end of a CAT5 cable into the square hole with the cable itself slipping through the side, slide the cable down, and place a padlock of your choice through the small hole at the top. Very useful for shutting down...
thingiverse
and specifically it is set up to be used for CAT5 cable (this one wont fit CAT6 but im working on one for that) however it should be OK to use for ANY 5mm Diameter cable so long as its round. also please note due to how i designed this theres a...
cults3d
... labeling tape. For better cable fit for Cat6 and Cat5 separately. It is advisable to use ABS or PETG filament, the PLA breaks easily. The v2 files are the modified versions. ...A little reinforced at the bottom of the clip, which was a bit fragile.
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=47956 Instructions Using the following options: 4th_plate_bottom_hole = none 3rd_plate_bottom_hole = none 5th_plate_bottom_hole = none 1st_plate = cat5e 4th_plate = none 2nd_plate = none...
thingiverse
I've provided my two STLs for wall-mountable, cable management for Cat5 cables. One was for my 5 port switch, and the other for my Draytek Router. The router (v2) has 4 cables at 15mm centres and a 40mm centre to the 5th. The switch (v1) model has 5...
thingiverse
Customized version of http://www.thingiverse.com/thing:47956 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=47956 Instructions Using the following options:...