kicker comp 10 with box 3d models

40 x 10 cents (0.10€ coins) is then equal to 4€ Update: Lid made narrower and the tube increased that now fits the number of coins needed. Diameter fits perfectly. The picture is of the 20 cent roll, the design is the same except for the lettering...

Support for Control Panel Housing for Creality CR-10(S) and Anet E10. It can be equipped with a 120mm fan (not required). Front or back, interchangeable. ... Timelapse: https://youtu.be/hqBexGnBw6M

https://www.thingiverse.com/apps/customizer/run?thing_id=734598 Instructions Using the following options: generate_lid = 1 bottom_height = 35 thickness = 1.8 generate_box = 1 lip_thickness = 0.8 y_width = 100 x_width = 100 lip_overlap_height = 2...

... WRX. ...To ensure an accurate fit, I employed an Xbox 360 Kinect to scan the trunk of the car and generate a precise STL model of the area where the sub box would be installed. ...The design was then printed using a Stratasys 450 MC with ASA material.

I built this little box to keep track of the packs of cigarette papers I bought. ...I'm happy to share it with you - it's not a grand project, but it gets the job done without any extra features or embellishments.

An industrial return air box, featuring three sides equipped with filters, efficiently recycles indoor air by capturing and cleaning contaminants before reintroducing the purified air back into the space. ...This design ensures optimal air circulation,...

I encountered issues with filament breaking right before the extruder overnight, so I designed the legs to lift the box by 100mm and protrude about 33mm on each side, making them a total of 189mm wide. It's crucial to accurately measure your box at...

SAAMI spec or factory ammo will fit with a good amount of room to spare.Fired shell casings will sit lower than live rounds, but internal supports will hold the case at the taper, so you will still be able to grab the rim to pull them out.My Odysee...

I've modified the control box design by removing the locator holes from the top of the box due to a slight variance in gap/spacing between the rubber feet and the box itself. This modification is still a work in progress, as I haven't had time to...

http://www.thingiverse.com/apps/customizer/run?thing_id=46394 Instructions Using the following settings: Fn is set to 20 Card spacing is at 4 units Gutter height is 2 units high Cube radius is 3 units wide Box height addition is boosted by 25 units...

The weapon box consists of two parts and is 120mm x 40mm x 20mm in size.

A box for tools that has a long service life and a low cost.

This is a scale tool box for your RC car equipment.

This scale tool box stores and organizes all of your RC car equipment essentials.

Made a ski box 56°NORD style for RC cars

Ammunition Container 1 of 10 (Secure Data Storage Enclosure)

Sega Mega Drive Cartridge Boy für 10 Module

I started using the original model for two of my CR-10's, but after printing the Shift31 legs, I realized that I couldn't get the feet attached because I was missing the old short legs to attach them. ...So, I designed this new one with holes for the...

... cradle the propeller blades, ensuring they remain stable and out of harm's way even during turbulent travel. This innovative design perfectly harmonizes form with function, effortlessly allowing the quadcopter to fit neatly into your bag or pocket.

... Used a little bit of candlewax to make the lid slide easily (until it wears in better). Customized version of https://www.thingiverse.com/thing:189264 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=189264

A protective Case for your original Hero 10 lens if you are using other lenses like the max lens mod. It will not last forever and requires an 0.1mm layer height to work. But prints in place and quick. Have fun with it. ...i might rework it.&nbsp;</p>

A much bigger receiver box for stock SCX 10ii. ...Did it for a friend and cannot find his photos anymore.

Custom box that can be stored under the heated bed of a cr10 mini to store tools.

Remix by mobiobi https://www.thingiverse.com/thing:4759177 inspired me to do the same but to fit a larger one plus 10 pro with phone case still on. Used the parametric Fusion 360 file from TheSameNameTwice, 85 x 182 x 24mm inside. as with...

The mount has been relocated to the front of the control box, allowing you to keep the spool holder in its original position while adding a cutout for the SD card slot and USB port. This holder includes all the tools that come with the machine, as...

I originally designed these legs for the control box of my CR-10S S4: https://www.thingiverse.com/thing:3178556 but once you install them, it's best not to move it around because the legs are unstable. So I created a bracket that can screw directly...

For the lids, there were two crucial points for filament changes: at 0.6 and 1.2 mm, while for the boxes, four key moments were marked: 56.8, 57.8, 61.8, and 62.8 mm. This was all done with a layer height of 0.2 mm. In my own print (check out the...

Files in STL format ready to print. ...For 1/10 scale trucks, can be resized.

This is just another set of legs for the control box. ... Similar style to the original, but just not as high.

A custom-designed Case Mounted Filament Holder is tailored to accommodate larger spools weighing up to 2.5kg, specifically for use with the Creality CR-10. I based this design on my own case dimensions, focusing on width, so if newer models have...