kid proof door locks 3d models
160994 3d models found related to kid proof door locks.prusaprinters
... were all to close together. I spay painted the 1"x4"x8' board white and screwed it to the wall and then added the hooks. The hooks are color coordinated per kid so they know exactly where to hang their stuff. https://www.mcmaster.com/90396A110/
thingiverse
Here is kid lock for glass doors. I printed it with PETg and it's works well! ... RUS: Простой и удобный детский замок на стеклянную дверцу шкафа из PETg.
thingiverse
My design could be used on any cupboard with swing or sliding doors, where door handle is mounted with single screw. You need to remove original door handles though. You could use screws from original handles if they are no longer than 20 mm. I...
thingiverse
Here is simple PETg printed kid door lock designed for double sliding alu-profile doors. ... RUS: Простой детский замок из PETg на дверь из алюминиевого профиля шкафа-купе.
thingiverse
These act as small handles as well as locks with the aid of pins made of coat-hanger wire to prevent curious reptiles sliding the doors open. The LEFT handle is 7mm longer than the right, because on my enclosure the left door is set back 7mm from...
thingiverse
...If there is an intruder, a person could slightly open the door and slide the part into the locked position. The locks in action can be viewed at...https://www.youtube.com/watch?v=dNxqyoSrQRc The original roller lock version might stick out too much.
thingiverse
having a baby at home makes you invent stuff:)) its a very simple design for baby proofing cabinet doors, enjoy. PS.: I have modified this designed as my wife was keep forgetting about it and breaking the thingy so the below design is a thicker...
thingiverse
This is flexible enough to bend when closing or opening a door when an adult is closing it, and not break, yet sturdy enough to prevent any doors from opening if in the locked state. Print this on it's side since the layer adhesion will not allow the...
thingiverse
A simple way to create a door for your Ultimaker 3d-printer. The Plexiglas dimensions for Ultimaker 3 is: Width: 30cm Height: 32cm Thickness: 4mm Two holes (3mm in diameter) at the bottom is 15 mm from the bottom and 52.5 mm from the sides.
thingiverse
I wanted a simple way to secure the doors while gone so I made this thingy that slides onto the bottom of the door then after closing the door you slide it over and it latches onto the door jam. It stays in place pretty well and even when they jump...
thingiverse
you will need: 2) 8-32x1.5" screws 10) m2x8mm screws 1) lever return spring print the spindle, and both door knob retainers with 100% infill all other parts were printed with 20% infill print spindle laying flat. I recycled my lever return spring...
thingiverse
Presenting the Cat-Proof, Child-Proof, Finger-smooshing proof Alligator Door-Stop!! The days of your fur-baby and/or human child locking themselves in and out of rooms due to accidental circumstances are NO MORE! Simply attach the Door Stop to the...
thingiverse
These are parts to help you make your dumb lock smart! ...Read my blog post for more info: https://blog.horner.tj/turning-a-dumb-lock-smart/
grabcad
My Extreme Redesign - Kid Friendly Door Stopper - is designed to stop a door from closing all the way when being opened or left alone which, therefore, acts as a kid safe way to leave doors open. Without my redesign, kids are prone to pen doors which...
cgtrader
Explosion-proof Door 3d model. This 3d model useful for interior and exterior visualizations, quality enough for close-up renders. Model are polygonal with turbosmooth modifier, stack not collapsed. Max file saved in two versions with Vray...
thingiverse
These prevent "lever" style door knobs/handles from being pulled down, they can only be pulled up to open the door. ...There's a slot for a captive M4 nut and a single bolt to clamp down on the handle.
grabcad
Little handles so my 2yo can open/close screen door without tearing the screen.
thingiverse
You can still lock the door by pushing your little finger through the hole on the cover. You can fix it with a zip tie. TOU MAY NEED TO MIRROR BEFORE PRINTING. All the sharp edges are smoothed for ziptie to work better. It is recommended...
thingiverse
My Son learned to open our Abus Door lock. So i needed a lock... for my lock. So i´ve design a Kids Safe 2 Part Puzzle, that my Kiddo doesn´t know to open. Additionaly i added a press fit for the Second part, that makes it harder to open to Puzzle. ...
thingiverse
My Son learned to open our Abus Door lock. So i needed a lock... for my lock. So i´ve design a Kids Safe 2 Part Puzzle, that my Kiddo doesn´t know to open. Additionaly i added a press fit for the Second part, that makes it harder to open to Puzzle.
thingiverse
I really liked JakeCape's door knob, but it had the wrong dimensions for what I wanted. ...I adapted it to fit the knob and keyholes of a standard US mortise lock set (antique door locks).
myminifactory
I really liked JakeCape's door knob, but it had the wrong dimensions for what I wanted. ...I adapted it to fit the knob and keyholes of a standard US mortise lock set (antique door locks).
prusaprinters
My Son learned to open our Abus Door lock. So i needed a lock... for my lock. So i´ve design a Kids Safe 2 Part Puzzle, that my Kiddo doesn´t know to open. Additionaly i added a press fit for the Second part, that makes it harder to open to Puzzle.
thingiverse
This is an add-on to the dog proof latch to make it more stable with doors that have large gaps between the floor and bottom of the door. It has a spring on the bottom to wedge between the door and latch. It also has an extra lip on the door side of...
thingiverse
If this is pressed when the button is facing downwards it locks into a slot of the inner sleeve and the door can be opened. Either a handle/lever or a knob can be attached to it. The knob has the advantage that it can be operated with one hand. ...
thingiverse
**Already been done?:** Yes, commercial versions are available, as well as some other Thingiverse designs, but all seem to require removing the door knob, installing a big lock-type unit (some with break-out pieces), then re-assembling the knob - a...