kingroon kp3 bltouch 3d models

Here are the parts needed to convert the Kingroon KP3 X Axis from a 20x20 V Slot Rail to a Precision Linear Rail system like the one used on the Y Axis: These components allow you to remove the V Slot Rail entirely and replace it with an affordable...

Just a good base to use when you are attaching to a 20x40 extrusion end like on the Kp3 and many others.

Files for the X axis and belt tensioner are also stored in the archive; they were taken from this website and modified to work with a KingRoon printer. ...I only modeled the Y-axis pulley housing myself, but it's a remix of someone else's work that I...

Adapter for sensor of plastic for 3D-printer KIngroon KP3

The fixing of the ultrabase for Kingroon KP3. ...https://youtu.be/8beM8AKK2Dw

The installation of the ultra-stable base system on the Kingroon KP3 unit is underway.

I got really tired of holding a flashlight to see my prints. So I opened the case and located a 24v lug that I could sure to power some leftover LED Strip lights and wired them up. Then I had to decide how to mount them and this is what I came up...

base.stl wFan.stl (Wind specialization ver) gFan.stl (General purpose ver) toplong.stl (long ver) topshort.stl (short ver) 5015 24v To install a blower fan With 80 cm wiring to extend the wiring M3-10mm 6 pieces M3-20mm 4 pieces 2 M3...

I build this foundation to support 2040 feet and secure a reliable Meanwell power supply beneath it.

for nut 10mm

I printed the original design but then made adjustments by trimming more than 2 inches from the parts that slide onto the pole. Next, I edited the file so it would produce shorter ends, mirroring those of the existing cap on the machine. ...To ensure...

I was tired of reaching under the print bed to try to make picks on the touch screen so I designed this adaptor and case. My ribbon cable had plenty of length to move the screen. For assembly I used the following hardware: To attach the Lower...

The Kingroon KP3 printer adapter is a specialized connector designed specifically to work seamlessly with the 3D printing sensors that come equipped on the KP3 model. ...Its primary function is to provide a secure and reliable connection between the...

SliceWorx design top handle for Kingroon KP3 Pro and S1 Use M5*25 hex cap head or button head screws for mounting this to any printer that has a 2040 extrusion vertical beam.Print settings:Orientation: Any flat sideLayer : 0.16 mmWalls: 3 top...

Initial printing attempts were thwarted due to changed specifications of the KINGROON KP3's hot end mounting position since the original data was created, preventing duct support installation. To rectify this, the original duct support stl file was...

I moved the mounting holes on the Satsana 5015 hotend/part cooling fan to line up with the Kingroon KP3 carriage. It is worth the upgrade and time spent. Leaves room on top to convert to direct drive if wanted. You can use the MODS that is for the...

This is a bltouch mount for Kingroon kp3s new Titan Extruder set. ... i use 2x m3_4 2x m3_6 2x m3_washer

Replacement Cover for Kingroon KP3 Printer Fits BTT/BIQU TFT35 V3.0 Touchscreen. I designed this upgrade to replace the Printer Control Board, utilizing a silent SKR Mini E3 with TMC2209's, and creating space for accessories like my EZABL Pro Power...

Parts that protect the SD card from gaps 20210111 Fine-tune the size of the card holes Added a characterless version of SD KP3_SDcade_N_ABS.stl KP3_SDcade_N_PLA.stl

no supports the original part from Kingroons page will either have the bltouch hit the plate when the pin is up, or if you relocate it higher the nozzle will hit. ... I relocated the holes down 2mm on the mounting holes, and took 2 mm off the thickness...

Customized version of https://www.thingiverse.com/thing:4837562 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=4837562

I remixed the spool holder for my KP3s in two Versions. V1.1 got tilted, a bit longer and fits on the printbed of a KP3s. V1.2 doesn't fit on the print bed of a KP3s so I printed it on my X1. ...It is even higher but has the same tilt.

I designed a custom solution allowing easy mounting of the power supply directly onto the wall behind my printer. To ensure secure attachment, I positioned it horizontally and used a pair of brackets to prevent movement or instability. ...The duplicate...

I remixed the spool holder for my KP3s in two Versions. V1.1 got tilted, a bit longer and fits on the printbed of a KP3s. V1.2 doesn't fit on the print bed of a KP3s so I printed it on my X1. ...It is even higher but has the same tilt.

This is Hybrid Filament Holder.

autolevel support for https://www.thingiverse.com/thing:4439842 sensor is a 18mm diameter.

Made this so i could mount the power supply on the wall behind the printer. Lay it on it's side to avoid supports, duplicate bracket because you will need two. ...Print Settings Printer: Creality CR-10 mini Rafts: No Supports: No Resolution: .02...

<p>Made this so i could mount the power supply on the wall behind the printer. ...Lay it on it's side to avoid supports, duplicate bracket because you will need two.</p> <h3>Print Settings</h3> <p><strong>Printer:</strong></p> <p>Creality CR-10 mini</p>...

I designed this setup specifically to allow easy installation of the power supply on the wall behind my printer. ...To prevent any interference from supports, I positioned it on its side, and since the bracket duplicates itself, I needed two of them.