kitchen faucet adapter for garden hose 3d models

Here is an adapter that screws onto standard 56/64-27 thread faucets (after removing the aerator) and allows a standard 1-1/6-11.5 garden hose to be attached to the other end. An additional o-ring or two may be required to prevent leaks. I would also...

Threaded adapter to connect a kitchen sink pull out faucet hose to a garden hose.

... ... This is an adpater that will allow you use to connect a water hose to the faucet. It can be customized for whatever project needed. For the time being it, is a work in progress. It is a pretty heavy customization of the nuts and bolts openscad.

... sand-cast outdoors faucet. ...Its dimensions are dubious, and the design is somewhat less than symmetric. To attach a standard garden hose fitting, I needed something that could be tightened enough to deform to fit the faucet. ...Hence this version. 

My sink faucet has 7/8-24 UNS thread type so I created an adapter to hook into a garden hose for Aquarium water changes. Internal bore is a cone for better flow and a stronger print. Print time was about 90mins. Hose threads fit extremely well,...

This is an adapter that goes between my Moen gooseneck faucet and a garden hose, so I can connect my sink to my fish tank syphon / refill adapter. The Moen faucet is some weird custom thread setup so I ended up having to put calipers on it to get...

Was surprised that this didn't exist already. ...took me a while to get something that worked. I can tell you that from the faucet to the adapter, there is no leakage. ...Your mileage may vary.

Hose adapter useful for connecting a homebrewing wort chiller to a kitchen faucet that has a Delta sprayer head. The sprayer hose has a non-standard connector. Unscrew the sprayer head and connect this adapter to the sprayer hose. Use some silicone...

Useful for connecting a homebrewing wort chiller to the kitchen faucet, when the faucet uses a Delta sprayer head. The sprayer hose has a non-standard connector. Remove the sprayer head and connect this adapter to the sprayer hose. Use a little...

This hose holder is made to mount on my garden faucet, to avoid further holes in the wall. ... The distance between the holes is 70mm.

Hose plug for outside faucet. Might help if you have a leak or you just want to cover it up. Washer can be printed but I would use TPU flexible filament! ...

Faucet with 3/4" Garden Hose Male Outlet 3/4" NPT Male Inlet Pipe Size, 1-1/4" Height Based on McMaster part #4792k62, from part image and listed measurements, not actual part. ... http://www.mcmaster.com/#4792k62/=zy9q7d

didn't like the other sink to garden hose adapters on here so i created this one, this one is designed to be harder to break the then rest of them hopefully you don't have to mess around with the scale when you print it

I was able to generate it with tinkercad and modify another adapter to make it a garden hose fitting which is the main fitting on the vacuum attachment. It's designed to print without supports. ...I recommend a good number of walls and to print in...

I was able to generate it with tinkercad and modify another adapter to make it a garden hose fitting which is the main fitting on the vacuum attachment. It's designed to print without supports. ...I recommend a good number of walls and to print in PETG...

The original handles were small and very hard to turn + not clear from their position if the faucet was openned or closedhere the arrow shows that when along the outlet it is openned and when perpendicular the flow is closedsame part for both sides...

Instead of carring a small pet bottle, connect the garden hose and have much fun!

53mm extension adapter for kitchen faucet with spray and hose as shown on the pictures.

A sunflower-themed garden hose faucet handle. This replaces the shattered plastic handle from a "Mansfield Frostproof" hose bib. It's adapted from a phyllotaxis simulation posted by Eric Buijs at https://www.youtube.com/watch?v=FOuHWXN8g2s , which...

- Extended 24mm part so it fits better for curved taps and holds better under pressure - Extended and increased hose part to fit 14mm diameter hose (base 13.8mm top 15mm, 20mm length) Thanks very much to CreativeTools.se

It's an adapter for connecting Gardena-hoses to kitchen faucets with a 3/8" thread Print instructionsI'm in the process of designing a outside-kitchen for our garden and needed an adapter for our IKEA kitchen faucet. ...Since I couldn't find any...

Adapt a garden hose to a Dyson vacuum cleaner. ... - take a piece of garden hose with inner diameter is 13mm, - place ti on the adapter -- secure it with a tightening collar. ...

I got "Nuanchu 2 Pcs Hose Inlet Strainer Filter Inlet Suction Strainer Garden Hose Strainer Filter Pump Inlet Strainer Sprayer Filter 7/8 Thread for Sprayer 390 395" from Amazon, thinking it would fit on a garden hose (needed to protect my battery...

This is a fitting for .625" OD x .5" ID hose for the Modular Hydroponic Tower Garden by smysnk. It press fits into the top-hose-thread.stl on his page. The inside diameter of this fitting is .375". ... Link to Modular Hydroponic Tower Garden by smysnk...

Adapter M26x1 to 26.5 (G 3/4) (Wasserhahn auf Gardena) Adapter to attach a gardena (or similar) garden hose to a faucet. ...Apapter um einen Gardena-Gartenschlauch (oder ähnlich) an einem Wasserhahn anzuschließen.

faucet for smoby kitchen...if you have broken one Print Settings Printer: Anet A8 Supports: Yes

I needed a quick adapter for my coil from a 20cm wide faucet head to a 7mm hose Figured someone else might need something similar one day so, enjoy :)

Faucet kit for children play kitchen very functional faucet has the following functions: Faucet only plugged Pipe swivel Handles rotatable Pressure single Additionally required: 2 screws for mounting handle Screw for mounting on the washbasin

... faucet adapter for substituting the one that got stuck inside a filter. ... Had to reverse engineer this connector, which sits between the faucet and the hose that is used for the shower, since I couldn't use the original made of metal anymore =/. ...

This is a removable Faucet to Hose Adapter. It is designed for my Aquarium Hose (6mm inner diameter). You need a sealing ring with a outer diameter of 20mm and a thickness of 1,5mm. ...You can glue the sealing ring to the adapter.