kite string spool 3d models

x 1/16” and 5/16” x 1/16” (I purchased from K&J Magnetics)ScrewsSuper glueAdditional designs used:Spool holder: https://www.thingiverse.com/thing:2486632Filament guide: https://www.thingiverse.com/thing:2228361Ikea Lack Grommet:...

I wanted the filament to share the same Cabin space as the printer, to maintain the same temperature and humidity since I found that it improves printing with certain materials.Also, it helps the filament move much better than from behind the...

Use this coaster to put down your favorite beverage or even the last 20 grams of filament on a spool - that's exactly what I'm going to do with mine, as I drink coffee and water the most. My print time for this model was an impressive 2 hours and 43...

Assemble the paddle at one end, insert the shaft halfway into the body and insert the spool and rubber band. Remove the open end of the shaft from the body and install the other paddle. After that, fit the deck into the cabin. The cabin can fit...

BOM is not update for enclosure.Update 2023-09-27Complete electronics & spool holder done. BOM also updated for enclosure.Update 2023-11-21Its completed and printing at 400mm/s at 15K just fine. I have gone for Rapid Burner toolhead, now you can...

If your bag doesn't fit this, don't worry - the base .IPT (Inventor) and .STEP files are included so you can adjust the model as needed. (PrusaPrinters does not currently allow .IPT uploads - check my Thingiverse listing for that.) Bag spool...

... Even with these features enabled, Ultimaker Cura 4.2.0 reported using only .85m of bracelet color and .33m of letter color, making this bracelet what I call a "remnant print" (printable with only a few "remnant" meters remaining on the spool(s)).

Use it to put down your favorite drink or make the most out of the last bit of filament on your spool. In my younger days, I used to read comics regularly - both from DC and Marvel. So, be sure to stick around for my Marvel coaster if this is...

Take a look at my other sidewinder X1 upgrades: https://www.thingiverse.com/thing:4783250 Artillery Sidewinder X1 Left X Cover with Cable Strain Relief https://www.thingiverse.com/thing:4784042 Artillery Sidewinder X1 Extruder Cover V4 w/ Strain...

Using the filament scale is straightforward: simply tare or zero it out with an empty spool to display the remaining filament weight. The first time you use it, you'll need to press the CAL button and adjust the gain to ensure accurate readings with...

To build the filament sensor housing, you will need: 1- One of the bearings that PRUSA includes with the MMU2 spool holders (∅22 ∅8 x 7.5 mm) 2- A magnet - The magnet housing in the plastic part is diameter 11mm x 2 mm length. I used a Neodymium...

Hot end parts are PETG(many others are too, cause im too lazy to change the spool) and PLA for pretty much everything else. I'd like to thanks the original Authors for their time and effort. I spent a few hours working on a few things to make...

The existing hole was too narrow, and filament got stuck there, causing the MMU2 to grind filament at the same time) I'm using auto rewind spools 3kg from vincent. They work great when they have some time on them(fresh ones don't work as great as the...

Other mods on my Voron V0: * The Ultimate Spool Holder by filamentry (https://www.thingiverse.com/thing:2047554) * V0 handles slim by Ch4rlesB (https://github.com/VoronDesign/VoronUsers/tree/master/printer_mods/Ch4rlesB/V0_Handles_Slim) * AC input...

:-) Added spool holder (by henryarnold) see references below to get files. Next modification will be power supply mount and a better board mount. Anyway, now it prints. March, 26, 2017 - First print done, calibration done. Everything is perfect. I...

... surface is in full contact with the dome. I am also using a modified filament tube holder at the back of the case, it is slanted and moves the feeding point closer to the center of the spool. ...You can find its 3D model in my account here as well.

A simple but effective filament storage system, using a few minimalist brackets connected by wooden dowels (or PVC pipes) that serve as railings for filament spools. The dowels/pipes can double as holders for paper towel rolls, tape, cables, etc. You...

I bought a new spool of FilaCube PLA 2, but it jammed the extruder as soon as the second print layer started. FilaCube recommended raising the temperature, determined by printing a temperature tower.Most temperature towers use way too much material,...

Known Problems: --threading the 1.75mm filament is a challenge if its tightly wound (end of the spool) --no practical application since i just use it the way it is Here's what you'll need: 1) NEMA 17 Stepper Motor 2) 11mm MK7 Drive Gear 3) U604ZZ...

I am still learning CAD - But I am hoping together we can bring something special to the community.Printing draft via Orca on 2 X1-CsMy ask is simple - Will you please help take this draft design to the next level with your skills and experience for...

I wanted a riser, that uses less than one spool of filament, is very robust, lets me open the top cover so that it stays open for ventilation, has a sufficent opening at the top to work on the printhead and of course has enough room for the AMS. So...

The uptake spool gearing is 3:1 so it runs at 20 RPM. Drive shaft to first plate is 1:4, so inner wrap is 240 RPM. The outer wrapping plate has an idler gear that's a tad larger so it's running a bit slower, probably around 200 RPM. The frame...

For the price of a decent case that can withstand being stuffed in a backpack, I can buy a spool of nylon or PETG filament and print two of them. Features: * Named parameter sets for angled vs. flat profiles, narrow vs. wedge-shaped, * Flat...

Please use the following format in your request: >Manufacturer: >Material Abbreviation: >Series: I have included a stand for use if you want to put the tags in front of the spool, useful for if you are building a filament cabinet like the one I...

This is a bracket that attaches to the filament spool area of the Fabtotum. It uses the already existing standoffs inside the plastic shell. To get this working correctly and optimally, you need to follow a few steps. 1. You must print this in...

(Pantah) The green parts are test prints from an old filament spool, used to check fit and feel as a printed part. The center section is Ø 52 mm with a slot for sandpaper to clean the bore. ...I adjusted the diameter by inserting paper under the...

You can also check out my other creations: - Locking Stone Box: https://www.thingiverse.com/thing:2875966 - Solar Light House: https://www.thingiverse.com/thing:2875991 - Hida a Key Flag Holder: https://www.thingiverse.com/thing:2882335 - Elephant:...

- Retractable cord reel: https://amzn.to/2VX62HB Modification and Assembly: *IMPORTANT* You MUST take apart the cord reel, tie a knot in the cable securing it in the spool, and another knot on the end with the keyring. The stock crimps are not strong...

I've included a 6-bearing spool holder for added convenience. If any conflicts arise or if you notice anything missing, please let me know. After further testing, I found that the leadscrew bearing holders cause some binding and wobble. Initially, I...

Remove any excess filament from the spool or reel. 2. Cut a suitable length of filament (typically around 10-20 meters). 3. Insert the filament into the printer's extruder tube, making sure it's seated properly. 4. Gently pull the filament to...