kk2 3d models
203 3d models found related to kk2.grabcad
Hobbyking KK2.1.5 Multi-rotor LCD Flight Control Board With 6050MPU And Atmel 644PA http://www.hobbyking.co.uk/hobbyking/store/uh_viewItem.asp?idProduct=54299
thingiverse
Soporte para KK2.15 para estructura F330 quadcopter http://www.hobbyking.com/hobbyking/store/__28172__F330_Glass_Fiber_Mini_Quadcopter_Frame_330mm.html...
thingiverse
Enclosure for the KK2 mini flight controller. Weight: Less than 8g (Solid ABS). Instructions To complete his build you will need: 4x M3x12 nylon screws Print at 0.1 layer height, solid. Cut M3...
thingiverse
Apply double-sided foam tape to the bottom of the KK2 board and place it into the case bottom. This will take up any slack and prevent the board from rattling in the case. Fasten the case top and bottom together with #4 X 5/8" wood screws; or just...
prusaprinters
I updated the design to have proper holes. Changes from 3dxl KK2.0 case design: Flipped the case upside down because I did not want to print supports. Unfortunately you loose the little notches on the buttons, but I found I could still press them...
thingiverse
3) Changed the screw layout on the base to fit this design: http://www.thingiverse.com/thing:32281 4) Added holes for the KK2.1 board buzzer and battery power port on the case. I did not change the lid at all, but I left a screw hole in the middle...
thingiverse
This is a simple case that I made for my KK2.1 board. It may fit other KK boards Like the 2.1.5 This case doesn't fit the 2.0 at this time. If there is enough interest I may mod it to fit the 2.0 also. ...
thingiverse
I really liked a certain KK2 board case, however it wouldn't fit on the quadcopter frame, therefore, I created some mounting brackets for use with the Mini Flame Wheel Style Quadcopter by tosjduenfs and the F450 KK2.1 Case and Mount by rcmanchild.
thingiverse
Reworked Moris's board mount to work with the KK2.1 iteration.
thingiverse
Just this case with the kk2.0 hole removed and the kk.21 holes added
thingiverse
I used Peter Larsen's top KK2.0 design and made a top for the new KK2.1 board. The bottom cases still work for the new KK2.1 board. I've included Peter Larsen's top, back case and buttons in this remix. Just corrected the scaling use some had...
thingiverse
http://www.rcproreviews.com/kk2-0-flight-controller-setup-and-settings/ 1: Turn on the transmitter and set the throttle to max. 2: Press down button 1 and 4, keep pressing until last step. Releasing the buttons aborts the calibration. 3: Turn on...
thingiverse
Hi, A way to protect your KK2.0 Board in your favourite multi rotor. The KK2.0 board was designed with a sample i got. The case is home designed : 6 parts (with the knobs) I'm currently looking for someone in order to get a 3D print prototype of...
thingiverse
Since it was hard to see kk2.1 the flight controller window by using original plate, I made a MHQ2 upper plate for the kk2.1.
thingiverse
... 1.5 mm, now it's 2mm. Each part got some new dimensions or design. Global dimensions are : 57x57x14.5mm Hope the KK2.0 board fit inside this new case At the moment i haven't got the KK2.1 board, So I can't make a design for it. ... Regards, Nick
thingiverse
I also know tons of people use the kk2 & KK2.1 boards. So this is a mount that connects directly to the flamewheel 450 top plate and has a top case that uses snaps to protect the top of the KK. This will work as a case if you don't have a F450 and...
cults3d
I also know tons of people use the kk2 & KK2.1 boards. So this is a mount that connects directly to the flamewheel 450 top plate and has a top case that uses snaps to protect the top of the KK. This will work as a case if you don't have a F450 and...
thingiverse
This is a small enclosure made for the Hobbyking KK2 flight-board. ...Its screw-less and has mounting points to be mounted by straps or tyreps on pretty much any quad-copter.
thingiverse
This mount holds the KK2 family of flight controllers from HobbyKing. ...The mounting points are placed so to line up with the prexisting holes in the BatBone frame from www.flitetest.com.
thingiverse
This is a vibration isolation mount for the KK2 family of quadcopter controllers (should fit any of the KK2 controllers. Shown in pics is the KK2.0). Mount will attach to the top plate of the Q450 quadcopter using existing fastener holes and...
thingiverse
... dampening bushings. ...So i create this adapter to fit a dampering for the KK2 board and other boards with 45mm between mounting holes. Printed with PLA at 20% infill without supports. ... Crossfire 2: http://www.thingiverse.com/thing:234867
thingiverse
I've made the holes 0.5mm wider, 0.4mm deeper and slightly tapered and now they should work with any KK2 board straight off the printer, at least they do that with my two KK2 boards.. I've added symbols above the buttons on the front just for...
thingiverse
:-D I made it to be able to carry my GoPro, KK2.1 board, EzUHF 8C diversity RX, video TX and 2200mAh lipo. Instructions I used a M3 tapper and M3 bolts to put it together. And 7 8mm anti...
pinshape
:-D I made it to be able to carry my GoPro, KK2.1 board, EzUHF 8C diversity RX, video TX and 2200mAh lipo. InstructionsI used a M3 tapper and M3 bolts to put it together. And 7 8mm anti vibration rubber damper between the clean board and the main...
thingiverse
This is a mount for the KK2.0 board on a BAH mini quad ( inside ), could possibly work on other mini quads frames as well but haven't tried yet. I have used double side tape to stick the mount to the frame and small self tappers to fix the board to...
thingiverse
Please not this will not fit the new kk-2.1 for sale at Hobbyking A low profile and light weight case for the Hobbyking KK2.0 Multirotor flight controler. I printed this on a UP! which deals with the overhangs on the lid For other printers I am not...
thingiverse
This frame is in multiple parts so it is easy to replace parts after a crash, everything is held together, including the the KK2.1 board and motors (depending on motors) with M3 screws or bolts (M3= 3mm diameter). Each arm is labeled with the...
thingiverse
Tweaker5 220mm : XT60 + SMA Antenna Mount + Piezo Buzzer Mount for KK2 KK2.1 by jbleazie & Figles, published July 29, 2016 *Second and third versions added. Inspired by Arakon & nickroosen concept.The Original design was for the Tweaker 180mm frame.