kk2 board 3d models
81163 3d models found related to kk2 board.thingiverse
Reworked Moris's board mount to work with the KK2.1 iteration.
thingiverse
This is a vibration isolation mount for the KK2 family of quadcopter controllers (should fit any of the KK2 controllers. Shown in pics is the KK2.0). Mount will attach to the top plate of the Q450 quadcopter using existing fastener holes and...
thingiverse
This frame is in multiple parts so it is easy to replace parts after a crash, everything is held together, including the the KK2.1 board and motors (depending on motors) with M3 screws or bolts (M3= 3mm diameter). Each arm is labeled with the...
pinshape
:-D I made it to be able to carry my GoPro, KK2.1 board, EzUHF 8C diversity RX, video TX and 2200mAh lipo. InstructionsI used a M3 tapper and M3 bolts to put it together. And 7 8mm anti vibration rubber damper between the clean board and the main...
thingiverse
:-D I made it to be able to carry my GoPro, KK2.1 board, EzUHF 8C diversity RX, video TX and 2200mAh lipo. Instructions I used a M3 tapper and M3 bolts to put it together. And 7 8mm anti...
thingiverse
But the very popular KK2.0 board has to be mounted orthogonally (that is facing with an edge to the front instead of a corner). ... So this thing is a modified top plate for mounting an orthogonal controller board such as the KK2.0 to an X-style...
thingiverse
When testing the fit with a friends KK board I notice that the newer boards have a JST connector for the buzzer,mine had a servo conector. We think the jst plug will still fit in the servo hole if you carefully swap the terminals so the plug will...
thingiverse
kk2.1.5 mounting board for X layout quadcopter
thingiverse
Apply double-sided foam tape to the bottom of the KK2 board and place it into the case bottom. This will take up any slack and prevent the board from rattling in the case. Fasten the case top and bottom together with #4 X 5/8" wood screws; or just...
thingiverse
I really liked a certain KK2 board case, however it wouldn't fit on the quadcopter frame, therefore, I created some mounting brackets for use with the Mini Flame Wheel Style Quadcopter by tosjduenfs and the F450 KK2.1 Case and Mount by rcmanchild.
thingiverse
I used Peter Larsen's top KK2.0 design and made a top for the new KK2.1 board. The bottom cases still work for the new KK2.1 board. I've included Peter Larsen's top, back case and buttons in this remix. Just corrected the scaling use some had...
thingiverse
Hi, A way to protect your KK2.0 Board in your favourite multi rotor. The KK2.0 board was designed with a sample i got. The case is home designed : 6 parts (with the knobs) I'm currently looking for someone in order to get a 3D print prototype of...
thingiverse
... dampening bushings. ...So i create this adapter to fit a dampering for the KK2 board and other boards with 45mm between mounting holes. Printed with PLA at 20% infill without supports. ... Crossfire 2: http://www.thingiverse.com/thing:234867
prusaprinters
I used #6 bolts from Home Depot. Changed the screw layout on the base to fit this design: http://www.thingiverse.com/thing:32281 Added holes for the KK2.1 board buzzer and battery power port on the case. I did not change the lid at all, but I...
thingiverse
3) Changed the screw layout on the base to fit this design: http://www.thingiverse.com/thing:32281 4) Added holes for the KK2.1 board buzzer and battery power port on the case. I did not change the lid at all, but I left a screw hole in the middle...
thingiverse
This is a simple case that I made for my KK2.1 board. It may fit other KK boards Like the 2.1.5 This case doesn't fit the 2.0 at this time. If there is enough interest I may mod it to fit the 2.0 also. ...
thingiverse
This is a small enclosure made for the Hobbyking KK2 flight-board. ...Its screw-less and has mounting points to be mounted by straps or tyreps on pretty much any quad-copter.
thingiverse
... 1.5 mm, now it's 2mm. Each part got some new dimensions or design. Global dimensions are : 57x57x14.5mm Hope the KK2.0 board fit inside this new case At the moment i haven't got the KK2.1 board, So I can't make a design for it. ... Regards, Nick
thingiverse
I've made the holes 0.5mm wider, 0.4mm deeper and slightly tapered and now they should work with any KK2 board straight off the printer, at least they do that with my two KK2 boards.. I've added symbols above the buttons on the front just for...
cults3d
I also know tons of people use the kk2 & KK2.1 boards. So this is a mount that connects directly to the flamewheel 450 top plate and has a top case that uses snaps to protect the top of the KK. This will work as a case if you don't have a F450 and...
thingiverse
I also know tons of people use the kk2 & KK2.1 boards. So this is a mount that connects directly to the flamewheel 450 top plate and has a top case that uses snaps to protect the top of the KK. This will work as a case if you don't have a F450 and...
thingiverse
This is a mount for the KK2.0 board on a BAH mini quad ( inside ), could possibly work on other mini quads frames as well but haven't tried yet. I have used double side tape to stick the mount to the frame and small self tappers to fix the board to...
thingiverse
User can access or remove the KK2.0 board by hands tool-less by lifting the swivel case up, this sometimes usefull for quick cleaning and maintenance purposes. ... More information, details and assembly can be found at this url:...
cults3d
User can access or remove the KK2.0 board by hands tool-less by lifting the swivel case up, this sometimes usefull for quick cleaning and maintenance purposes. ... More information, details and assembly can be found at this url:...
grabcad
Hobbyking KK2.1.5 Multi-rotor LCD Flight Control Board With 6050MPU And Atmel 644PA http://www.hobbyking.co.uk/hobbyking/store/uh_viewItem.asp?idProduct=54299
thingiverse
Soporte para KK2.15 para estructura F330 quadcopter http://www.hobbyking.com/hobbyking/store/__28172__F330_Glass_Fiber_Mini_Quadcopter_Frame_330mm.html...
thingiverse
Enclosure for the KK2 mini flight controller. Weight: Less than 8g (Solid ABS). Instructions To complete his build you will need: 4x M3x12 nylon screws Print at 0.1 layer height, solid. Cut M3...
thingiverse
Simple boards to attach different Flight controllers to basically any frame with hole spacing to fit a KK2 board. Instructions I use zip-ties to attach the FC to the conversion board and the supplied screws to mount the board to the frame. ...This...