klipper config for anycubic predator by 3d models

Dies ist meine Halterung der Beaglecam für den Anycubic Vyper.Der Mast ist drehbar und die Camera mit der Klemmschraube stufenlos Höhenverstellbar.Da mein Vyper höhere Füße hat müssen für die original Drucker höhe der Stützfuß und der Mast...

The cap's intricate design was created using Anycubic's vibrant green resin, expertly cured under a UV lamp. To assemble it, first print the cap, then carefully fill its interior with your preferred substance. ...After that, let the filled cap cure...

Para que quede la boquilla a la misma altura que la original, la parte superior del soporte debe estar a unos 6mm del borde del carro X adapter to install a Creality mk8 hotend in the Anycubic Chiron. Fully compatible with the height sensor and...

Para que quede la boquilla a la misma altura que la original, la parte superior del soporte debe estar a unos 6mm del borde del carro X adapter to install a Creality mk8 hotend in the Anycubic Chiron. Fully compatible with the height sensor and...

Totalmente compatible con el sensor de altura y caja original, también es compatible con éste diseño de caja https://www.thingiverse.com/thing:3195516 No es necesario hacer ninguna modificación a carro X, se usan los agujeros del soporte del V5...

All the parts of the model have been cut so as to be printed vertically, for a higher quality of printing Predator Predator is a 1987 American science fiction action film directed by John McTiernan and written by brothers Jim and John Thomas.[4] It...

config that i use to print: Esun PLA+ layer height 0.21mm infil 25% tree support

I have a resin 3D printer, an Anycubic Photon Mono 4K specifically. When I print things, the buildplate remains wet and a lot of resin gets wasted when I remove the part and clean the plate, so i designed this drainer so to make the plate drain...

Drainer to hang the plate inclined 20 degrees for better draining after the printing process. ... I have improved the design by tilting it also around the other axis to concentrate the resin on one vertex of the printing base.

When assembling this part, users can take advantage of the existing factory screw hole and utilize the supplementary hole for added stability. Printing from ABS is highly recommended because PLA often fails to properly plasticize when printing with...

The Acer Predator x27 has a really loud fan and intake is blocked by the vesa mount, so I disabled the monitors fan and made this to fit a 92mm noctua fan using 50mm m4 screws. ...Printed with PETG for rigidity.

It serves as a stress-reliever for the Bowden tube and provides a mounting point for the hot end wiring. 3. **Volcano Parts**: If you plan to use Volcano with your J6 hot end, these parts can be used to extend the setup by 10mm, which is not ideal...

I was inspired by a design on Thingiverse to create a sleeve that could be filled with activated charcoal granules. I printed the parts using my Photon 3D printer, applying standard tilt and auto-support settings at a 0.1mm layer height, resulting...

Mount for an RaspberryPi Camera

a little modify for 4010 centrifugal fan

a little modify for 4010 centrifugal fan

Remixed arm for 1/4" screw hole for cameras. Check the original thingiverse for the mount and pin. ...Might make a horizonal version later on.

part required: 1x v2 cable chain top end 1x v2 cable chain down end 12x cable chain middle 1 8x cable chain middle 2 22x cable chain lid 17mm you need 20x middle parts, start from top whit "v2 cable chain top end" and finish whit "v2 cable chain down...

...If you decide to use this holder, make sure to pair it with a 40x40x10 fan and radiator setup. A 40x40x20 fan and radiator combination is actually part of the standard system configuration, so that's what you'll get by default – no radiator included.

This knobs are an adaptation from ones made by MKingCharles. I've modified it to suit my V1 i3 Mega which has different knobs made of metal. There are two files: Cool wheel = This one is just plug and play, print it and it's ready to go. Cool...

... Chain Top End" and ending with the "V2 Cable Chain Down End". ...From top to bottom, you should assemble seven pieces of "Cable Chain Middle 1", followed by eight pieces of "Cable Chain Middle 2", and finally five pieces of "Cable Chain Middle 1".

Cooler for AnyCubuc Stepper Motor. ... For 2 fans 50x50x10 (I have the Noiseblocker XS-1 BlackSilentFan Fan (50x50x10mm)) installed. Those who take the original screws from the fan, holes must be drilled afterwards. ... A lot of fun printing again.

... for Assembly over the Clamps of Z-Axis End Switches. ...Usable for 8 and 10mm LED Strips. The Longest Part Without Connector Can Be Printed in One Piece Diagonally in Chiron. The Longest Part For Connector Is Split and Requires Connector to Connect.

This is especially important for thermal sensitive materials such as PET, abs or nylon. With this fairlead there aren't drafts of air that ruin your printed objects. I have attached the file with the project for fusion360 (* .fd3). It is editable,...

Base for nozzles, designed to know which nozzle you have placed in the 3D printer, as sometimes it is not known which nozzle is placed.

To eliminate the need for the shipped spatula, I created this custom tool that can reach all edges of the vat. This design allows me to extract more resin without soaking it in a towel for final cleaning. ... This project combines the precise results...

After spotting tennis balls isolating my feet, I made up my mind to create a slightly smaller version for use with Racquetballs. ... I've attached a file for a ring that snugly fits around a racquetball if you'd like to review it beforehand.

These are some knobs for the screws, if you don't have some for an allen key. You need a nut to secure it. ...It's pressfit, so you might need to push a little harder or resize to fit your screw and nut dimensions.

...Supports are required to print.\r\n\r\nUPDATE2:\r\n° Extra room has been provided for X limit switch wiring.\r\n° Based on feedback, an extra 2.5mm of clearance has been added for the Z flag fasteners. The Z flags file I have here is still required.

... to firmly attach it to the probe. For Version 2: Utilize the original screws on the probe for attachment. Verify that the protector is 0.2~0.8mm thicker than the switch body. Adjust the height if necessary. ... This has been tested with a V1 probe.