klr dash 3d models
4320 3d models found related to klr dash.thingiverse
Customized version of https://www.thingiverse.com/thing:1099603 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=1099603
thingiverse
Broke the choke lever on a 1st Gen KLR. Why pay $19 when the printer is sitting idle? Maybe not quite as ergonomic as the original but perfectly functional. Reuses the original housing and fits tight with just enough drag. If it does print too...
thingiverse
This is from the latest generation KLR saddle bag and is the first part you break when you crash it. ...Print a mirror fot the other side.
thingiverse
Fits 2008 and up KLR 650 and possibly others. Replaces the rubber section of the turn signals. ... You will need 4 #10 x 1.25" screws to secure them.
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=101307 Instructions Using the following options: Keychain_Style = Block build_plate_selector = 0 build_plate_manual_y = 100 build_plate_manual_x = 100 text9 = text8 = text7 = text6 = text5 =...
thingiverse
I made this cover to replace a lost air box cover for Kawasaki KLR 250 97-200x bikes. ... I printed mine solid out of PETG however you dont need to.
thingiverse
I modeled up this fender cap so I could cut down my fender to help mitigate wobbling at higher speeds on Gen 1 KLR's. The model isn't great, it was one of my earlier ones, but the weird geometry doesn't look bad when printed. To measure your fender...
thingiverse
Designed for '08-'18 KLR 650. The rotor side has yet to be tested but the dimensions are based on the actual part. I would recommend only as a patch job until the real spacer is available and with plenty of grease. More durable filament such as ABS...
cults3d
Designed for '08-'18 KLR 650. The rotor side has yet to be tested but the dimensions are based on the actual part. I would recommend only as a patch job until the real spacer is available and with plenty of grease. More durable filament such as ABS...
thingiverse
Remove the headlight cowling from the KLR (the 2 phillips and the 4 M6 bolts). 3. Disconnect the headlight and turn signals 4. Remove the light cover 5. Raise the light lock 6. Remove the old light bulb 7. Put the adapter with the widthest part...
thingiverse
A slightly improved and easier to print KLR/KLX choke lever from danboyts original design. Has a textured thumb grip, flat bottom for less overhang challenges, and I altered some of the angles slightly so that if you set support angle to 79...
thingiverse
Customized version of http://www.thingiverse.com/thing:1148986 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=1148986
thingiverse
Customized version of https://www.thingiverse.com/thing:3867358 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3867358
thingiverse
Customized version of https://www.thingiverse.com/thing:682146 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=682146
thingiverse
Customized version of https://www.thingiverse.com/thing:682146 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=682146
thingiverse
Customized version of http://www.thingiverse.com/thing:45576 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=45576
thingiverse
Customized version of http://www.thingiverse.com/thing:834725 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=834725 Instructions Using the following options: twist =...