knife sharpener tool 3d models
124903 3d models found related to knife sharpener tool.thingiverse
Most handy knife sharpener tool Compatible with standard 158x22x9mm whetstones 16, 20, 25, 30 angle guides included Sucker cups not included
thingiverse
This is a simple attachment to a knife sharpening tool allowing to make a convex edge. The standard model allows for 10.7 degree angle variation and R32 with my machine, the holes are for 8mm rods and fit tight without glue. ... I am not a professional...
thingiverse
You can also improve any similar Knife sharpening tool that uses a metal rod with a diameter of 8 mm. One of the stops will need to be fixed on the rod, this requires a single screw M3 length of 15-20 mm with a hidden head. Upgrade yuor Knife...
thingiverse
- Created smaller angle guides, you need these to be able to set the angle on the knife itself, to compensate for knife angle. ## Hardware needed: - 2x 10mm diameter x 180mm aluminum rod/tube for the body - 6mm (or 10mm) diameter x 280mm aluminum...
prusaprinters
Hardware needed:2x 10mm diameter x 180mm aluminum rod/tube for the body6mm (or 10mm) diameter x 280mm aluminum rod/tube for the handle1x M5x20 hex head bolt + Washer + Thumb Nut for knife guide.1x M5x 20 hex head bolt + nut for handleglue to fix rods...
thingiverse
Made an angle guide holder for CNCKitchen's Knife Sharpening Tool V2.1 :-) Since it's angled and not stepped the tolerances can be a little tight for the last few guides.
thingiverse
The body of the knife sharpening tool v2.1 uses a 10mm tube. Since it's very hard to find metric tubing in the states, I ended up buying a 3/8 inch tube. The original plan says you should be able to get away with a 3/8 inch tube instead of a 10mm,...
prusaprinters
Knife Sharpener My make of theKnife Sharpener This is a collection of all remixes that fit my needs, in order to make the Knife Sharpener. The only part I design myself is the end cap for the 10mm pipe. Most of the parts are not from this design, but...
prusaprinters
I was inspired by another 3D printed knife sharpener (http://www.dr-henschke.de/Messerschleifer.html) and adapted the design for relatively cheep Chinese water stones as you can find them on Aliexpress. ...Additionally I simplified the geometry to...
thingiverse
# Knife Sharpener My make of the **Knife Sharpener** This is a collection of all remixes that fit my needs, in order to make the ``Knife Sharpener``. The only part I design myself is the end cap for the 10mm pipe. Most of the parts are not from...
thingiverse
I was inspired by another 3D printed knife sharpener (http://www.dr-henschke.de/Messerschleifer.html) and adapted the design for relatively cheep Chinese water stones as you can find them on Aliexpress. Additionally I simplified the geometry to...
thingiverse
Thanks to CNCKitchen for this great model, finally my knifes are razorsharp again! I added some holes to be able to screw the Feet and Base to the Aluminium rod. I Used a massive 10mm Aluminium Rod, but using a tube is also fine. The screws I...
thingiverse
For this remix you still need the original files from https://www.thingiverse.com/thing:1274297 I designed additionally: - one knob to use instead of the M5 thumb nut - one knob to use for the file handle - a stopper so that the file-handle can not...
thingiverse
I recently made a sharpener based on the original model (https://www.thingiverse.com/thing:1274297) and needed to change a few details to improve it. There are two general problems with the original design: * All holes for the 10mm rods/tubes are...
thingiverse
I made a new guide for https://www.thingiverse.com/thing:1274297 to eliminate the backlash. You can print an insert for tubes of 6 or 8 mm. Halves stick together on superglue. For mounting I used the bolt and nut M5. ...In the original version, the nut...
thingiverse
This is a remix of CNCKitchen's guide but for a larger whetstone and a different handle. The end of the whetstone is 30.07mm x 59.15mm, the length is unimportant as you move the clamps to fit so the clamp's stl is to fit this. I've added a new...
thingiverse
This is a compact box to store your sharpening stones (link below) and sharpening tool guides. The holes in the bottom help the moisture and with unloading the stones if stuck. I recommend printing hindges with petg, but pla will also work. They...
thingiverse
The idea is that you tighten the jig onto your knife, providing the blade has a reasonable size flat near the backbone as mine does, and it will guide strokes against a stone at a constant 20 degree angle. I will be printing this in the next...
thingiverse
I modified the Knife Sharpening by JediRAMA to fit my magnets (5 units, 30×4×2mm prisms) and a ø10mm tube for both the vertical shaft and the horizontal stabilizer. This was done in OpenSCAD through boolean operations, hence on top of the .scad...
thingiverse
I printed the Guide Holder for Knife Sharpening Tool V2.1 (thank you @Arlin710) and my guides are too loose inside it, so I made a Lid to keep them inside the holder.
thingiverse
The original design of this works great for double bevel blades but I needed something that would go a little lower for mine. The original parts were in black and the remixed parts are purple. I have added the F360 file if you need to tweak...
thingiverse
The rods that I bought ended up being ~ 9.5mm instead of 10mm So I made this ~3mm spacer to shim the gap
thingiverse
It was challenging finding 10mm tubes here in the states so I used 6mm tubes throughout instead. ...They can be easily found here: https://smile.amazon.com/gp/product/B07KJ4NWNG I modified that parts that would have used 10mm tubes so they fit 6mm...
thingiverse
The original model for the GuideBody1 part has a hole that is closed so it does not need supports but the height of the closing layer is not good for the default settings in PrusaSlicer at 0.2mm layer height. The closing layer is between two layers...
thingiverse
I already have 10 mm diameter magnets but unfortunately they are 3mm thick instead of 2mm from the design of Stefan. I have slightly modified the opening of the pocket holes so my magnets should fit. The pocket holes thickness is the same as they are...
thingiverse
Just a Sandpaper holder. ... Used Mirror Tape to fixate the Sandpaper to the adapter.
thingiverse
Holds 3 170x75 thin plates as in : http://s.click.aliexpress.com/e/o0hMnElS I chose 3 progressive grits : \#800 for establishing the initial bevel (this one is to be used with parsimony or in case of a dent) \#1200 for monthly bevel maintenance (out...
thingiverse
This is an add-on for the CNC Kitchen's knife sharpening tool. I didn't really like the way magnets are holding the knife (especially if it's a bigger one) in the original design, but I also didn't want to redo the whole base. ...This allows you to...
thingiverse
This is a JIG to be attached to a Dremel Rotary Tool and used to sharpening Knifes. It complies the mosto common sharpening angles on 2 pieces (17/25 degrees and 14/20 degrees) so you can print the one is mostly suitable for your use. ... The models...