kobalt tool hanging system 3d models
237777 3d models found related to kobalt tool hanging system.thingiverse
This is a little something I whipped up to hang my 24v Kobalt tools from the underside of a bench, or in my case some cabinets.
thingiverse
1x1 Gridfinity module designed to hold a Kobalt deburring tool. Should work for any deburring tool 17mm in diameter or less. - Holes have been designed to eliminate sagging or the need for supports (stepped holes). ... - Based on the Gridfinity...
thingiverse
Designed and printed wall mounts for various Kobalt 24v tools. Reciprocating Saw (requires supports) Oscillating saw and Hand Light Impacts and Impact Driver Skill Saw High Speed Drill Battery Mounts The spacer was designed to evenly space...
thingiverse
This is a first attempt at making a tool holder for the Kobalt Router table. It is printed in two parts to avoid using supports. The pieces will be bonded with glue. This holds two inserts, the 1/2" collet, the starting pin, wrench, and lift allen...
thingiverse
The Kobalt 80v trimmer uses a loading method where 6 foot of trimmer line is run through the head, and then bump feed is turned to coil the line inside. The problem is that there's nothing to grab hold of, and as it turns the bump feed will retract...
thingiverse
... If you print in another material or in a different orientation you may need to adjust clearances to get press fit of the locking bar and clean hanging of the hangers on the rails. More recently I printed the new trash bin in PETG. ... Worked fine.
prusaprinters
This was designed to hold a set of SAE and Metric sockets and wrench and be compatable with Alex Chappel's assortment system grid.Has wells for the socket wrench, socket extender, drive adapter, 3 Dewalt socket adapters, and 15 metric and 13 SAE...
thingiverse
I wanted to hang my Kobalt 24 volt hand tools from the underside of my shelf, so I built these a few months back. The current STL's are my third version, and allow for countersunk screws, no supports required, & prints in just around an hour for each...
thingiverse
Inspired by the other Kobalt 24v tool holders I set out to make my own. These provide a very good and strong fitment. I added a spacer for the tools that require it. ... The circular saw requires 2 spacers.
thingiverse
This is a tool holder mount for the Kobalt 24v Max line of tools. The tool holder definitely works for the drill, impact driver, and circular saw, and probably others with similiar dimensions. I will be designing further refined versions for the...
cults3d
This print, shown in gray/silver, allows us to use a 40 volt Kobalt (Lowes Home Improvement store house brand) battery with a 40 volt Greenworks tool, but only the tools that carry the batteries externally. My Greenworks blower works and it looks...
thingiverse
This print, shown in gray/silver, allows us to use a 40 volt Kobalt (Lowes Home Improvement store house brand) battery with a 40 volt Greenworks tool, but only the tools that carry the batteries externally. My Greenworks blower works and it looks...
thingiverse
I picked up a set of metric and inch T-Handle Kobalt hex wrenches because Home Depot had them on clearance. Great hex wrenches...crappy holder. So...I designed this to sit on my tool table. It holds the hex wrenches. It's got labels for each wrench...
thingiverse
This is a hanging system I've been working on for quite some time. ...With this system you can hang basically anything anywhere. It's completely adjustable to any dimensions. ... https://www.youtube.com/watch?v=A_qAFD6op-8
thingiverse
https://www.lowes.com/pd/Kobalt-1-Piece-Black-PVC-Storage-Rail/3374252 Fusion 360 share link: https://a360.co/2QT5hc3 The profile matches very close to the original part and the original flex pads fit in place without the need for glue in my case. ...
thingiverse
A simple system for hanging lots of spools, this makes it easy enough to replace a spool or two without having to move around all spools just to replace one. In the pictures I'm using 8 mm smooth rod for the hangers and M8 threaded rod to hang the...
thingiverse
I was getting a bit sick of my hats just sitting on my tables, so I quickly designed and made this hat, and other related stuff-hanging system. The dowels friction fit into the wall hangers, with the hat hangers using the wall, and the dowel to...
myminifactory
These two 3D printed parts allow you to recycle a 250 ml can into a hanging storage system. You mount the top bracket under a cabinet, glue the can bracket to the can, and you can store objects in the can and then slide the container into the...
myminifactory
Hanging baskets are hard to water when full of growing plants, this simple system allows the water to be distrubuted directly to the plant roots. Simply attach the funnel to the drinks can and pierce the can with as many small holes as desired, bury...
thingiverse
One of my original Gardena hanging system rings went missing. I thought there would be a replacment print somewhere on the internet. But i couldn't find one so i made this one myself. easy to print with prusa mk3s. Do with it as you please. A...
prusaprinters
A simple system for hanging lots of spools, this makes it easy enough to replace a spool or two without having to move around all spools just to replace one. In the pictures I'm using 8 mm smooth rod for the hangers and M8 threaded rod to hang the...
thingiverse
... loosing horizontal surface space. I wanted it to be rackable, so that plants and holders can be removed, without disturbing other plants in the same system. This is my first attempt. ... I like it :-) https://youtu.be/-tRfj5Dz0yI
myminifactory
This is a picture hanging system specifically designed for the IKEA STROMBY range of picture frames. The minimum you need to print in order to hange a typical A4 sized frame is two "Picture hanger top Angled" pieces. These are very simple items,...
thingiverse
---------- ### My complete Spannerhands MK6 System build: https://www.thingiverse.com/make:674461 I liked the idea of TrevJonez's Spannerhands Spool-holder rail-mount, but since my boxes are going to have all their weight on these slides, I wanted a...
cults3d
My complete Spannerhands MK6 System build: https://www.thingiverse.com/make:674461 I liked the idea of TrevJonez's Spannerhands Spool-holder rail-mount, but since my boxes are going to have all their weight on these slides, I wanted a wider surface...
pinshape
Didn't want to drill wholes in my newly painted wall to hang some canvas picture frames. Easy to print. I used PETG. The chains I used are here https://www.thingiverse.com/thing:28405.When using PETG to print the chains you can cut them open and...
cults3d
... without loosing horizontal surface space. ... I wanted it to be rackable, so that plants and holders can be removed, without disturbing other plants in the same system. This is my first attempt. ... I like it :-) https://youtu.be/-tRfj5Dz0yI
cults3d
... without loosing horizontal surface space. ... I wanted it to be rackable, so that plants and holders can be removed, without disturbing other plants in the same system. This is my first attempt. ... I like it :-) https://youtu.be/-tRfj5Dz0yI