kobra max firmware 3d models

Kobra 2 Plus is a high speed machine and make a lot of vibration with stock feet.You need to print 4 of them and 4 yellow dots squash balls

I change some design from this model (https://www.thingiverse.com/thing:5203968) to lower the tightness of filament sensor cable and move the sensor more toward the printer thus remaining all screw in place ****This parts is only suitable for those...

This is a quick way to verify that your bed levelling and Z offset is calibrated and/or to find areas on your build plate that are best avoided if possible.Included is the STL file and a program that can be run directly on an Anycubic Kobra 2...

Posted is a gantry/printhead cover for the Anycubic Kobra Max and Vyper printers with open fan shrouds. This design reduces noise caused from the fan shrouds on the stock cover. Other than the openings for the fans, as well as a small opening at...

To setup a CURA Profile for your QIDI X-Max, download the X-Max.3mf and open in CURA as a project. Please save the attached file to your USB drive, do not put them in the folder. Then proceed with the instructions below to update: 1. Power off...

This is a replacement for the legs that come on these printers. ...It is a way to dampen the vibrations in the printer and whatever it is resting on.

This bracket relocates the spool from the side of the machine to the front left corner of it so there is a smaller footprint.

Ledbar for Ender 3s1 designed to fit Ikea Ledberg ledstrips.Optional endcaps for that clean look.

This is for redirecting the filament feed from the front/left corner of the printer. ...This works great with my filament spool holder.

This is a remix for those of you that have the Bondtech direct drive upgrade. Also if you have an enclosure this mount will actually line your spools up with the access flap at top. I changed the design in Fusion 360 free version. I am a beginner,...

This will adapt a pad 7 to the front of a bigtreetech pad7. ...You will need to swap belt tensioners out for this...

MUST USE TPU if you want these to cushion your printer and dampen vibration. The TPU I used is rated 95A for softness. No supports needed if printed in the correct orientation. The spool footing fits nicely on the bottom where it would normally...

A filament guide I made to suit my setup but sharing just in case anyone else wanted to use it as well. Does require a longer screw to mount and a hole drilled in the proper area to mount. I do not have the capability to put the hole in the end to...

This is a work in progress, i have not printed it yet but will update if needed.

I've designed a SCAD version of the STL I found earlier (https://www.thingiverse.com/thing:5416449). So you can adjust it's length or other parameters. There's also sample rod included that will fit in a hole. Please adjust to your needs. ... ...

Just a simple camera mount. The camera can be placed on top. ...I will revise this form in a timely manner so that the camera can be attached with a screw and the cables have a guide.

Added the Marlin 2.0.7.2 firmware for the Ender 3 Max based off the Ender 3 Pro firmware but supporting the larger bed size and filament runout sensor. I used the 5 pin header on the board to connect the BLTouch but had a 3 + 2 pin bltouch cable. One...

These instructions are especially designed for the Dual Head & Auto Level printer from Max Micron with the official custom Marlin firmware from Max Micron. The steps are similar for other printers, but some details could change! Download the...

Small part to stabilize the PTFE tube of my Anycubic Vyper and Anycubic Kobra Max printers

Petite pièce pour stabiliser le tube PTFE de mes imprimantes Anycubic Vyper et Anycubic Kobra Max

A marvellous piece of out-of-the-box thinking, impressive engineering!Best thing is: the logic works with the Anycubic Kobra 2 Max without touching the firmware, just connect it instead of the original sensor. This version of the smart spool holder...

Note: The Kobra Max and the Vyper use one fan header for both part cooling fans so you will need to splice the two 5015 together. The led on the Kobra can be cut and run through the hole directly under the heat sink fan, or hot glued or super glued...

The K15 Diesel was designed to fit the Anycubic Kobra Max and the Anycubic Vyper. The front plate attaches with M3 screws and the shroud connects to the base with with factory screws. Comes with two face plates. One with led mount and one...

The K15 Diesel was designed to fit the Anycubic Kobra Max and the Anycubic Vyper. The front plate attaches with M3 screws and the shroud connects to the base with with factory screws.</p> <p>Comes with two face plates. ...One with led mount and one...

... the tightener bolt hole on the side. Just added it as an extra option.Work Great with this Top Middle Mount Spool Holder: https://www.printables.com/model/647877-anycubic-kobra-2-max-top-middle-mount-spool-holder Hardware:  required 1 x M3 Bolt

I mixed both to a special version for Kobra Max. The Vyper should be the same. You will need ruthex threathed inserts (M3) https://www.amazon.de/gp/product/B08BCRZZS3/ref=ppx_yo_dt_b_search_asin_title?ie=UTF8&psc=1 I used a 4020 cooler instead...

 I have designed this locator to fit the Anycubic Kobra 2 Max.  Note: 2 models the difference is the clearance on the side to the gantry/motor.  Some machines require a narrow model which is the 2mm version.I replaced the screws for the cable harness...

You will need the roller and 2 spacers from this:https://www.thingiverse.com/thing:3052488Update: I strengthened the base where the piece zip ties to the Kobra and added 2 slots to keep the zip ties in place better. I also added a slot to outside the...

I would like to share a new guide for the max to change the position of the filament to front of the printer .it also guides the filament when going to max height .

Additionally 4M3 hex bolts, 2 to connect the two halfs together around the hotend, then another 2 M3 bolts to secure the assembely to the strain guageThe design of the original hotend made things challenging but Ive come up with a solution to the...