korg hat 3d models

Additional top panel overlay for Korg NTS-1. Fits well but because it is quite thin you might want to use some double-sided tape to keep it flat. I left a cutout for the keyboard and to be able to see the original labels. Knobs are just some I had...

Tired of forgetting what the knobs do on your Korg NanoKontrol Midi Controller? Here's a couple of custom knob caps labeled A & B, with a big tactile pointer as a bonus. The hole diameter is 6.25mm, which gives a good fit when printing on my...

Still using my old KORG Pandorra for warm ups. Needed a holder for my desk.Fits perfect. Requires a M4 or M3 screw for hinge (not part of the print layout) print vice with min. 60% infill or it will break Update: the holder incl. in the...

The Korg LP350 Digital Piano suffers from a widespread issue known as "squeaky pedals." This problem arises due to inadequate support under the pedals box, causing the bridge that holds them to produce a creaking sound every time a pedal is pressed.

I'm a bit short on surface space, so I decided to mount my three Volcas above the shelf where my Korg Monologue synth is currently sitting. It's standard Rubbermaid "Twin Track" shelving - the kind you often find in closets. I designed and 3D...

This is an adapter designed for mounting the Korg SQ-1 sequencer within a Eurorack modular synthesizer case. For the lower section, I created two legs that prevent the SQ-1 from falling backwards inside the case and enhance its stability. These are...

Korg LP350 Digital Piano has a common problem called "squeaky pedals". Because of the inadequate pedals box support, the pedals and the bridge that holds them will eventually start producing a creaking sound each time a pedal is pressed.</p> <p>This...

Hi For all of you who find the original knobs on the KORG monoton Delay too small (like me). I have designed a knob according to my ideas. This Knob should not only be larger, but also feel good to the touch and should also be useful in use, in no...

A case for the Korg NTS-1, with compartments for a jack cable and the supplied USB cable. The cover is held in position by two Ø5x2mm magnets. A magnetless version is available, tight tolerances hold the cover in place by friction.</p> <h3>Print...

This 18HP adapter will integrate Korg NTS-1 into eurorack so that all its connectors are facing front. The adapter will mount the main board of the NTS-1 at 90 degree angle. In addition to printing the adapter you need the following: 14 short...

Human stencils are a crucial tool for creating accurate and precise drawings.

<p>Pen Holder for the touch screen pen<br/> You can attach it with a double side ribbon</p>

Customized version of https://www.thingiverse.com/thing:1588641 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=1588641

Customized version of https://www.thingiverse.com/thing:3223715 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3223715

The perfects button to replace broken part on KORG M1

This is remix for first version korg nano kontrol

Based to Korg's 3d files I made side panels with text Korg and Nu-tekt on it.

3d model korg low polygons to print Simil Marvel Movie Collection

This is a cover for the Korg Pitchblack+ tuner's battery compartment. It could possibly fit other Korg pedals as well. Possibly even on other equipment. ... Print Settings Printer Brand: Ultimaker Printer: Ultimaker 3 Rafts: No Supports: Yes

Simple, light press fit sleeves for the tiny Korg knobs. ...Opening at one end so LED is still visible.

Custom Korg NTS-1 Faceplate CYBERPUNK edition, two versions included, one with bottom bar below ribbon keybord, the other without.

Supports a Korg GA-30 Guitar/Bass tuner so it can stand nearly upright (tilted at 15 degree angle).

A replacement slider/fader knob for KORG nano KONTROL usb mixer control. ... Prints without supports but supports could be useful anyway.

These are simple touchpad covers for the Korg KP3 (+) that should work for the kaossilator as well. V2 has a waffle type bottom in case you wanted to line the bottom with a soft material of some sort. ...  

Mount the Korg NTS-1 to the Aturia Keystep. Print the holder two times, once for left and once for right. I also added double sided tape to permanently mount the NTS-1 to my Keystep. ...

Press fit POT upgrades for the Korg Volca series. They fit over the narrow stock POTs, not replace the existing knobs of the unit. ...Print in clear or semitransparent material to allow the light to show through.

Korg nanoKontrol2 holder for Arturia Keystep for my perfect DAW setup. ...You can use the original screws for attachment.Printer: Ender 3 V2Filament: PLAInfill: 25%Duration: 2h per partSupport: not necessary

Got a Snap Dragon SnapAxe folding guitar?Got a Korg PX4 series Personal Effects Processor?Then this could be useful to you, as it allows you to attach your PX4 onto your SnapAxe.